Operation CHARM: Car repair manuals for everyone.

Transmission Component Overviews






Transmission Component Overviews

Transmission housing cover and 5th gear, removing and installing. Refer to => [ Transmission Housing Cover and 5th Gear ] Transmission Housing Cover and 5th Gear.

Transmission, disassembling and assembling. Refer to => [ Transmission ] Transmission.





I - => [ Transmission Housing and 5th Gear Cover ]

II - => [ Transmission Housing and Shift Mechanism ]

III - => [ Input Shaft, Output Shafts, Differential and Shift Forks ]

Transmission Housing and 5th Gear Cover





1 Bolt

• 18 Nm

• Cover to transmission housing.

2 Transmission Housing Cover

• Note that oil will leak out when the cover is removed with the transmission installed.

• The transmission fluid must be drained and filled again. Refer to => [ Transmission Fluid, Checking and Filling ] Service and Repair.

3 Gasket

4 Bolt

• 80 Nm + 90° (1/4) additional turn.

• Always replace.

• Hold with the adapter on the plate spring bolt head in position

• Remove any locking compound residue from the threaded holes for the synchronizer hub and 5th gear bolts using a thread tap. Otherwise, there is the danger that the bolts could shear off.

5 Concave Washer

• Installing, refer to => [ Installed Position
of Plate Springs for 5th Gear Synchronizer Hub and Drive Gear Bolts ] Transmission.

6 Bolt

• 25 Nm

• For the pivot pin to the transmission housing

7 Pivot Pin

8 5th Gear Selector Fork

• Disassembling and assembling, refer to => [ Shift Forks ] Shift Forks.

• Adjusting, refer to => [ Adjusting 5th Gear ] Transmission.

9 Spring

• Offset version.

• Installing, refer to => [ Installation of Offset
Springs ] Input Shaft.

10 5th Gear Locking Collar

• Installed position, refer to => [ Assembling 5th Gear
Locking Collar/Synchronizer Hub ] Input Shaft.

• Adjusting, refer to => [ Adjusting 5th Gear ] Transmission.

11 Locking Pieces

• Installed position => [ 5th Gear Synchronizer ] Input Shaft.

• Quantity: 3

12 Synchronizer Hub with Gear Wheel and 5th Gear Synchronizer Ring

• Remove together with the transmission housing, refer to => [ Transmission ] Transmission.

• Removing individually, refer to => [ Transmission Housing Cover and 5th Gear ] Transmission Housing Cover and 5th Gear.

• Disassembling and assembling, refer to => [ Assembling 5th Gear
Locking Collar/Synchronizer Hub ] Input Shaft.

13 Needle Bearing

14 5th Gear

• Remove together with the transmission housing, refer to => [ Transmission ] Transmission.

• Removing individually, refer to => [ Transmission Housing Cover and 5th Gear ] Transmission Housing Cover and 5th Gear.

• Installed position, refer to => [ Installed Position,
5th Gear ] Transmission.

Transmission Housing and Shift Mechanism





1 Bolt

• 25 Nm

2 Flange Shaft with Pressure Spring

• Removing and installing, refer to one of the following:

=> [ Left Flange Shaft and Seal ] Left Flange Shaft and Seal

=> [ Right Flange Shaft, Seal and Sleeve, Two Piece ] Right Flange Shaft, Seal and Sleeve, Two Piece

=> [ Right Flange Shaft, Seal and Sleeve, One Piece ] Right Flange Shaft, Seal and Sleeve, One Piece

• Assembling, refer to => [ Differential ] Service and Repair.

3 Bolt

• 25 Nm

• For the reverse shaft support.

• Self locking.

• Always replace.

4 Bolt

• 30 Nm

• For the reverse shaft support.

• Self locking

• Always replace.

5 O-ring

• Always replace

6 Pivot Pin

7 Bolt

• 25 Nm

8 Bolt

• 25 Nm

9 Sealing Cap

10 Bolt

• 25 Nm

• For the reverse shaft support.

• Always replace.

11 Bolt

• 5 Nm

12 Transmission Neutral Position Sensor (G701)

• For vehicles with the start/stop system.

13 Transmission Housing

• Remove together with 5th gear, refer to => [ Transmission ] Transmission.

• Disassembling and assembling, refer to => [ Transmission Housing and Clutch Housing ] Transmission Housing and Clutch Housing.

14 Clutch Housing

• Disassembling and assembling, refer to => [ Transmission Housing and Clutch Housing ] Transmission Housing and Clutch Housing.

15 Bolt

• 25 Nm + 90° (1/4) additional turn.

• Always replace.

16 Selector Lever with Selector Cover

• (Shift unit)

• Disassembling and Assembling, refer to => [ Shift Unit ] Shift Unit.

17 Bolt

• 25 Nm

Input Shaft, Output Shafts, Differential and Shift Forks





1 Differential

• Disassembling and assembling, refer to => [ Differential ] Service and Repair.

2 Seal

• Quantity: 4

• Always replace.

3 Output Shaft

• Disassembling and assembling, refer to => [ Output Shaft ] Output Shaft.

4 Reverse Gear Shaft Support

• Disassembling and assembling, refer to => [ Reverse Shaft ] Reverse Shaft.

5 Reverse Shaft

• Disassembling and assembling, refer to => [ Reverse Shaft ] Reverse Shaft.

6 Input Shaft

• Disassembling and assembling, refer to => [ Input Shaft ] Input Shaft.

7 Reverse Gear Selector Fork

• Disassembling and assembling, refer to => [ Shift Forks ] Shift Forks.

• Installed position, refer to => [ Transmission ] Transmission.

8 Bolt

• 25 Nm

9 Selector Fork with Rail

• (Shift forks)

• Disassembling and assembling, refer to => [ Shift Forks ] Shift Forks.

10 Clutch Housing

• Disassembling and assembling, refer to => [ Transmission Housing and Clutch Housing ] Transmission Housing and Clutch Housing.

11 Nut

• 25 Nm + 90° (1/4) additional turn.

• 4 nuts for the bearing mount.

• Always replace.

12 Flange Shaft with Pressure Spring

• Removing and installing, refer to one of the following:

=> [ Left Flange Shaft and Seal ] Left Flange Shaft and Seal

=> [ Right Flange Shaft, Seal and Sleeve, Two Piece ] Right Flange Shaft, Seal and Sleeve, Two Piece

=> [ Right Flange Shaft, Seal and Sleeve, One Piece ] Right Flange Shaft, Seal and Sleeve, One Piece

• Assembling, refer to => [ Differential ] Service and Repair.

13 Bolt

• 25 Nm