Operation CHARM: Car repair manuals for everyone.

Subframe, Stabilizer Bar and Control Arms Assembly Overview






Subframe, Stabilizer Bar and Control Arms Assembly Overview


• Welding and straightening work on supporting or wheel carrying components of suspension is not permitted.

• Always replace self-locking nuts.

• Always replace corroded bolts/nuts.






1 Nut

• 65 Nm

• When tightening, counterhold on hex socket head of joint bolt.

• Self-locking

• Always replace if removed.

2 Coupling Rod

• Linking stabilizer to suspension strut.

3 Bracket

• Locating, refer to => [ Securing Console ] Front Suspension.

• If a console is replaced, alignment must be checked. Refer to => [ Wheel Alignment ] Wheel Alignment.

4 Mounting Bracket

• Locating, refer to => [ Securing Mounting Bracket ] Front Suspension.

• With bonded rubber bushing

5 Bolt

• 50 Nm + 90° turn

• Always replace if removed.

6 Bolt

• M12 x 1.5 x 90

• 70 Nm + 90° turn

• Always replace if removed.

7 Bolt

• M12 x 1.5 x 90

• 70 Nm + 90° turn

• Always replace if removed.

8 Left Front Level Control System Sensor (G78)

• Removing and installing, refer to => [ Front Left Level Control System Sensor ] Front Left Level Control System Sensor.

• Can be checked in Guided Fault Finding using the vehicle diagnosis, testing and information system (VAS 5051B).

9 Bolt

• 9 Nm

10 Control Arm

• It is possible there are different control arm versions (steel, aluminum).

• For the correct allocation, refer to the Electronic Parts Catalog (ETKA).

• Do not install control arms made of different materials on the right and left sides.

• Replace with ball joint if damaged.

• Removing and installing, refer to => [ Control Arm with Mounting Bracket ] Control Arm With Mounting Bracket.

• Replace bearing, refer to => [ Control Arm Bonded Rubber Bushing ] Service and Repair.

11 Control Arm

• it is possible there are different control arm versions (welded sheet steel, single sheet steel).

• For the correct allocation, refer to the Electronic Parts Catalog (ETKA).

• It is permissible to interchange control arms welded sheet steel, single sheet steel, from right to left.

• Replace with ball joint if damaged.

• Removing and installing, refer to => [ Control Arm with Mounting Bracket ] Control Arm With Mounting Bracket.

• Replace bearing, refer to => [ Control Arm Bonded Rubber Bushing ] Service and Repair.

12 Nut

• M12 x 1.5

• 60 Nm

• Self-locking

• Always replace if removed.

13 Ball Joint

• Checking, refer to => [ Ball Joint, Checking ] Procedures.

• Removing and installing, refer to => [ Ball Joint ] Removal and Replacement.

• Replace with control arm if damaged.

14 Nut

• Cast steel control arm: 60 Nm

• Steel and aluminum control arms: 100 Nm

• Self-locking

• Always replace if removed.

15 Nut

• 9 Nm

• Self-locking

• Always replace if removed.

16 Bolt

• M12 x 1.5 x 100

• 70 Nm + 90° turn

• Always replace if removed.

17 Bolt

• 20 Nm + 90° turn

• Always replace if removed.

18 Bolt

• M12 x 1.5 x 75

• 70 Nm + 90° turn

• Always replace if removed.

19 Bolt

• M14 x 1.5 x 70

• 100 Nm + 90° turn

• Only tighten when pendulum support is bolted to transmission.

• Always replace if removed.

20 Underbody Protection Bracket

• For the correct allocation, refer to the Electronic Parts Catalog (ETKA).

21 Bolt

• M10 x 75

• 50 Nm + 90° turn

• Always replace if removed.

22 Bolt

• M10 x 35

• 50 Nm + 90° turn

• Always replace if removed.

23 Bracket on Pendulum Support

• No replacement part

24 Pendulum Support

• Bolt first to transmission, then to subframe.

• Various versions.

• For the correct allocation, refer to the Electronic Parts Catalog (ETKA).

25 Lower Bonded Rubber Bushing for Pendulum Support

• Pressing out and in for vehicles with FWD, refer to => [ Subframe Bonded Rubber Bushing, FWD ] Subframe Bonded Rubber Bushing, FWD.

• Pressing out and in for vehicles with AWD, refer to => [ Subframe Bonded Rubber Bushing, AWD ] Subframe Bonded Rubber Bushing, AWD.

• For the correct allocation, refer to the Electronic Parts Catalog (ETKA).

26 Shield

• For FWD vehicles only.

27 Bolt

• 6 Nm

• Self-tapping

28 Subframe

• Various versions.

• Removing and installing without steering gear, refer to => [ Subframe without Steering Gear ] Subframe Without Steering Gear.

• Removing and installing with steering gear, refer to => [ Subframe with Steering Gear ] Subframe With Steering Gear.

• For the correct allocation, refer to the Electronic Parts Catalog (ETKA).

29 Upper Bonded Rubber Bushing for Pendulum Support

• Pressing out and in for vehicles with FWD, refer to => [ Subframe Bonded Rubber Bushing, FWD ] Subframe Bonded Rubber Bushing, FWD.

• Pressing out and in for vehicles with AWD, refer to => [ Subframe Bonded Rubber Bushing, AWD ] Subframe Bonded Rubber Bushing, AWD.

• For the correct allocation, refer to the Electronic Parts Catalog (ETKA).

30 Bolt

• M12 x 1.5 x 110

• 70 Nm + 90° turn

• Always replace if removed.

• Always tighten threaded connections in curb weight position. Refer to => [ Wheel Bearing, Lifting to Curb Weight Position ] Procedures.

31 Nut

• 65 Nm

• When tightening, counterhold on hex socket head of joint bolt.

• Self-locking

• Always replace if removed.

32 Stabilizer Bar

• Various versions.

• For the correct allocation, refer to the Electronic Parts Catalog (ETKA).

• Removing and installing, refer to => [ Stabilizer Bar ] Stabilizer Bar.

Identifying the Pendulum Support Bonded Rubber Bushing






• There are two different versions of the pendulum support bonded rubber bushing: the T version - I - and the V version - II -.

• For the correct allocation, refer to the Electronic Parts Catalog (ETKA).

I The corners on the inner core - 1 - face toward the opening for the pendulum support - arrow - (T version).
II The corners on the inner core - 2 - face away from the opening for the pendulum support - arrow - (V version).