Oxygen Sensor Regulation Behind Catalytic Converter, Checking

Diagnostic Procedures

Oxygen Sensor Regulation Behind Catalytic Converter, Checking

• Vehicle must be raised before the electrical connector for the Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) (G130) is accessible.

• When servicing terminals 3 and 4 in the electrical harness connector of the Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) (G130), use only gold-plated terminals.

Special tools, testers and auxiliary items required

• Multimeter.

• Wiring diagram.

Test requirements

• The Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) (G130) fuse OK.

• Oxygen Sensor (O2S) 1 (behind Three Way Catalytic Converter (TWC) Heater ( G130) OK. Refer to the repair information.

• Battery voltage at least 12.5 volts.

• All electrical consumers such as, lights and rear window defroster, switched off.

• Vehicles with automatic transmission, selector lever in position " P" or "N".

• A/C switched off.

• Ground connections between engine/transmission/chassis OK.

• Exhaust system between catalytic converter and cylinder head properly sealed.

• Coolant Temperature at least 80 °C.

Test procedure

- Perform a preliminary check to verify the customers complaint. Refer to => [ Preliminary Check ] Preliminary Check

• If an O2 sensor heater code is also set, perform the test for the O2 heater first.

Start diagnosis

- Connect scan tool.

- Start the engine and let it run at idle.

- Select "Diagnostic mode 6: Check test results of components that are not continuously monitored".

- Select "Test-ID 02: Oxygen sensor monitoring behind catalytic converter".

- Select following Test-IDs.

- Check the specified values at idle.





If the specified values were obtained:

- Switch ignition OFF. Fault is not active at this time. Check for poor connections, loose terminals and harness check.

If the specified values were Not obtained:

- Remove the right vehicle floor cover - arrows -.





Checking primary voltage

- Disconnect the brown Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) (G130) electrical harness connector - arrow -.





- Switch the ignition ON.

- Using a multimeter, check the Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) (G130) electrical harness connector terminals 3 to 4 for voltage.





Specified value: 0.400 to 0.500 Volts

- Switch the ignition OFF.

If the specified value was obtained:

- Replace the Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) ( G130) Refer to the repair information.

If the specified value was Not obtained:

Checking wiring

If the manufacturers test box is being used, perform the following step.

- Install the test box.

If the manufacturers test box is not being used, perform the following step.

- Remove the Motronic Engine Control Module (ECM) ( J623). Refer to the repair information.

- Using a multimeter, check the Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) ( G130) electrical harness connector terminals to the Motronic Engine Control Module (ECM) (J623) electrical harness connector terminals for an open circuit according to the wiring diagram.









Specified value: 1.5 ohms Max.

If the specified value was Not obtained:

- Check the wiring for an open, high resistance or short to ground.

- Check the electrical harness connector for damage, corrosion, loose or broken terminals.

- If necessary, repair the faulty wiring connection.

If the specified value was obtained:

- Replace the Motronic Engine Control Module (ECM) (J623). Refer to the repair information.

- Install the right vehicle floor cover - arrows -.





Final procedures

After the repair work, the following work steps must be performed in the following sequence:

1. Check the DTC memory. Refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Scan Tool Testing and Procedures.

2. If necessary, erase the DTC memory. Refer to => [ Diagnostic Mode 04 - Erase DTC Memory ] Scan Tool Testing and Procedures.

3. If the DTC memory was erased, generate readiness code. Refer to => [ Readiness Code ] Monitors, Trips, Drive Cycles and Readiness Codes.