Operation CHARM: Car repair manuals for everyone.

Removal and Replacement






03 - Service Procedures


Engine Oil, Draining or Extracting, Changing Oil Filter and Filling Oil

• Engine Oil, Draining or Extracting

• Oil Filter, Replacing

Engine Oil, Draining or Extracting

Special tools, testers and auxiliary items required

• Oil extractor (V.A.G 1782 )





• Oil absorbent towel (VAS 6204/1)

Engine Oil, Draining or Extracting

Perform the following work procedure:

• In engines with standing oil filter module, oil filter should be changed before changing engine oil. Removing the filter element will open a valve and oil in the filter housing will flow automatically into the crankshaft housing.

• If engine oil is drained and not extracted using old oil extraction unit, replace oil drain plug. This prevents leaks.

• Observe waste disposal regulations!

- Extract engine oil using old oil collecting and extracting unit (V.A.G 1782).

Or

- Remove oil drain plug

- Let engine oil drain.

• Observe waste disposal regulations!

- Screw in new oil drain plug with sealing ring hand-tight.

Torque specifications for oil drain plug:

The torque specifications are dependent on engine code.

CAUTION!
• Torque settings must not be exceeded

• A torque figure that is too high may lead to leaks or even damage the oil pan.

- Fill up with engine oil, Note oil specification.

Oil Filter, Replacing

• Oil Filter, 2.5L, Replacing

• Oil Filter, TDI PD, Replacing

• Engine Oil, Filling

Oil Filter, 2.5L, Replacing

Special tools, testers and auxiliary items required

• Oil drain adapter (T40057)





• Oil filter wrench (VAS 3417)





• Torque wrench (V.A.G 1331/)

• Needle-nose pliers

Oil filter housing, emptying

CAUTION!
• Oil filter housing must be drained before it is removed.

• When screwing in oil drain adapter (T40057 ), a valve in the oil filter housing is opened.

• If oil drain adapter (T40057) is unscrewed again, the valve closes automatically again.

- Unscrew dust cap - arrow - from oil filter housing.





- Screw oil drain adapter (T40057) into oil filter housing and hold hose into an oil collecting pan.





- Allow engine oil to drain.

- Unscrew oil drain adapter (T40057 ) again.

The drain valve - 1 - should seal flush with the under side of the oil filter housing - 2 -.





Oil filter insert, removing

- The oil filter housing can be loosened using the oil filter wrench (VAS 3417).

- Then unscrew by hand and remove together with oil filter insert.

- Remove oil filter insert - 2 - from oil filter housing center tube - 4 -.





Sealing ring, removing

CAUTION!
The oil filter housing sealing ring - 3 - must be replaced each time the oil filter insert is changed - 2 - or every other time the oil filter housing is loosened.

The sealing ring is equipped with a so-called "service flag " - A -.

• The sealing ring can be gripped at the "service flag" - A - with a suitable tool and then removed from the seal groove.

- Remove sealing ring - 1 - from oil filter housing seal groove - 2 - by pulling sealing ring out with needle-nose pliers - 3 - on the "service flag" - arrow -.





Sealing ring, installing

- Lubricate sealing ring - 3 -.





- Lay sealing ring in oil filter housing seal groove so service flag - A - is aligned toward top.

- Press sealing ring into seal groove and check whether ring contacts entire groove evenly by feeling above sealing ring with finger - arrows -.





Oil filter insert, installing





- Press new oil filter insert - 2 - onto oil filter housing center tube - 4 - as far as stop.

Oil filter housing, installing

- Install oil filter housing - 4 - with new sealing ring - 3 - and new oil filter insert - 2 - by hand until almost on oil filter housing stop - 1 -.

- Tighten the oil filter housing - 2 - to 25 Nm.





- Install dust cap - arrow - hand-tight in oil filter housing.

Oil Filter, TDI PD, Replacing

Removing

• Observe waste disposal regulations!

• Oil new O-rings before installation.

Loosen sealing cap - arrow - e.g. using ring wrench AF 36 or using socket insert AF 36 (T10125 ).





• Loosen cap before draining/extracting so that engine oil can flow out of filter housing.

- Clean sealing surfaces at cap and at oil filter housing.

Installing





- Install oil filter - 3 -

- Replace O-rings - 2 and 4 -.

- Install screw cap - arrow - and tighten to 25 Nm.





Installation is reverse of removal.

Engine Oil, Filling

Note oil specifications.

General Information

• Observe waste disposal regulations!

- After the oil is filled, wait 3 minutes and then check the oil level.

- Pull out oil dipstick and wipe with clean rag. Replace dipstick and push down to stop.

- Pull out dipstick again and read oil level.

If the dipstick appears as illustrated:





A Oil must not be topped off.
B Oil can be topped off. After topping off, oil may be in range - A -.
C Oil must be topped off. It is sufficient when oil level is in area - B - (grooved field).

If oil level is above area - A -, the catalytic converter can be damaged.

- When oil level is below marking - C -, top off with oil to marking - A -. Note oil specification.