Operation CHARM: Car repair manuals for everyone.

Heated Oxygen Sensor, Engine Code BEW, Checking






Heated Oxygen Sensor, Engine Code BEW, Checking

• Applies to Engine Code (BEW) only

• Oxygen Sensor (O2S) Heater (Z19) is part of Heated Oxygen Sensor (HO2S) (G39) and cannot be serviced separately.

• When servicing terminals in the electrical harness connector of Heated Oxygen Sensor (HO2S) (G39), use only gold-plated terminals.

Special tools, testers and auxiliary items required

• Multimeter.

• Wiring diagram.

Test requirements

• Fuse (S13) OK.

• Battery voltage at least 12.5 volts.

• All electrical consumers such as, lights and rear window defroster, switched off.

• Vehicles with automatic transmission, shift selector lever into position " P" or "N".

• A/C switched off.

• Ground (GND) connections between engine/transmission/chassis OK.

• Ignition switched off.

Test procedure

- Perform a preliminary check to verify the customers complaint. Refer to => [ Preliminary Check ] Preliminary Check.

Start diagnosis

- Vehicle must be raised to access Heated Oxygen Sensor (HO2S) (G39)

- Access to Heated Oxygen Sensor is beneath synthetic cover at vehicle floor.

- Disconnect the Heated Oxygen Sensor (HO2S) (G39 ) electrical harness connector.

Checking internal resistance

- Using a multimeter, check the Heated Oxygen Sensor (HO2S) (G39) terminals 3 to 4 for resistance.





Specified value: 2.5 to 10.0 ohms (at approx. 20° C)

If the specification was not obtained:

- Replace Heated Oxygen Sensor (HO2S) (G39).

If the specification was obtained:

Checking voltage supply

Crank the engine.

- Using a multimeter, check the Heated Oxygen Sensor (HO2S) (G39) electrical harness connector terminal 4 to Ground (GND) for voltage.









Specified value: Battery voltage.

Switch the ignition off.

If the specification was not obtained:

- Check the wiring from the Heated Oxygen Sensor (HO2S) (G39) electrical harness connector terminal 4 to the Power Supply Relay (terminal 30, B+) (J317) socket 2/30 for an open circuit, a short circuit to Battery (+), or Ground (GND).

- Check the electrical harness connector for damage, corrosion, loose or broken terminals.

- If necessary, repair the faulty wiring connection.

If the specification was obtained:

Checking Ground (GND) activation

If the manufacturers test box is being used, perform the following step.

- Install the test box.

If the manufacturers test box is not being used, perform the following step.

- Remove the Diesel Direct Fuel Injection (DFI) Engine Control Module (ECM) (J248). Refer to => [ Engine Control Module, Replacing ] Engine Control Module, Replacing.

- Using a multimeter, check the Heated Oxygen Sensor (HO2S) (G39) electrical harness connector to the Diesel Direct Fuel Injection (DFI) Engine Control Module (ECM) (J248) electrical harness connector T94 for resistance.





Specified value: 1.5 ohms.

If the specification was not obtained:

- Check the wiring for an open circuit, a short circuit to Battery positive (+) or Ground (GND).

- Check the electrical harness connector for damage, corrosion, loose or broken terminals.

- If necessary, repair the wiring connection.

If the specification was obtained:

- Erase the DTC memory. Refer to => [ Diagnostic Mode 04 - Erase DTC Memory ] Diagnostic Mode 04 - Erase DTC Memory.

- Perform a road test to verify repair.

If the DTC does not return:

Repair complete, Generate readiness code. Refer to => [ Readiness Code ] Readiness Code.

- End diagnosis.

If the DTC returns and no malfunction is found in the wiring and voltage supply was OK:

- Replace the Diesel Direct Fuel Injection (DFI) Engine Control Module (ECM) (J248). Refer to => [ Engine Control Module, Replacing ] Engine Control Module, Replacing.

Assembly is performed in the reverse order of the removal, note the following:

Final procedures

After repair work, the following work steps must be performed in the following sequence:

1. Check the DTC memory. Refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

2. If necessary, erase the DTC memory. Refer to => [ Diagnostic Mode 04 - Erase DTC Memory ] Diagnostic Mode 04 - Erase DTC Memory.

3. If the DTC memory was erased, generate readiness code. Refer to => [ Readiness Code ] Readiness Code.

End of Diagnosis