Operation CHARM: Car repair manuals for everyone.

Air Conditioning Unit (For Hatchback)

DISASSEMBLY




1. REMOVE DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY
a. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the defroster damper control cable.




2. REMOVE AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY
a. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the air mix damper control cable.




3. REMOVE NO. 1 AIR DUCT
a. Disengage the 3 claws and remove the air duct.




4. REMOVE NO. 2 AIR DUCT
a. Disengage the 3 claws and remove the air duct.




5. REMOVE PTC HEATER ASSEMBLY (for Cold Area Specification Vehicles)
a. Remove the 2 screws and the PTC heater.




6. REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY
a. Disengage the 3 claws and remove the clamp.




b. Remove the heater radiator unit from the air conditioner radiator assembly.




7. REMOVE COOLER EXPANSION VALVE
a. Using a hexagon wrench 4, remove the 2 hexagon bolts and detach the cooler expansion valve.
b. Remove the 2 O-rings from the cooler evaporator.




8. REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
a. Disengage the cooler thermistor connector.




b. Remove the 3 screws.
c. Disengage the 4 claws and remove the heater case lower.




d. Remove the cooler evaporator.




9. REMOVE NO. 1 COOLER THERMISTOR
a. Remove the cooler thermistor from the cooler evaporator.

REASSEMBLY




1. INSTALL NO. 1 COOLER THERMISTOR
a. Install the sensor onto the evaporator as shown in the illustration.
b. Check that the sensor sticks to the evaporator surface as shown in the illustration (A: Sensor, B: Evaporator).

NOTE: If reusing the evaporator, do not reinsert the sensor in the same position that it was in before. Insert it within area C shown in the illustration.




2. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

HINT: If a new cooler evaporator is installed, add compressor oil to the cooler evaporator as follows.

Compressor oil: ND-OIL8 or the equivalent. Add 40 cc (1.35 fl. oz.)

a. Install the cooler evaporator.




b. Engage the 4 claws and install the heater case lower.
c. Install the 3 screws.




d. Engage the cooler thermistor connector.




3. INSTALL COOLER EXPANSION VALVE
a. Apply sufficient compressor oil (ND-OIL8) to 2 new O-rings and the fitting surface of the cooler expansion valve.

Compressor oil: ND-OIL8 or the equivalent

b. Install the 2 O-rings onto the cooler evaporator.
c. Using a hexagon wrench 4, install the cooler expansion valve with the 2 hexagon bolts.

Torque: 3.5 N.m (36 kgf.cm, 31 in.lbf)




4. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
a. Install the radiator heater unit onto the air conditioner radiator assembly.




b. Engage the 3 clips and install the clamp.




5. INSTALL PTC HEATER ASSEMBLY (for Cold Area Specification Vehicles).
a. Install the PTC heater with the 2 screws.




6. INSTALL NO. 2 AIR DUCT
a. Engage the 3 claws and install the air duct.




7. INSTALL NO. 1 AIR DUCT
a. Engage the 3 claws and install the air duct.




8. INSTALL AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY
a. Engage the claw and install the air mix damper control cable.




9. INSTALL DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY
a. Engage the claw and install the defroster damper control cable.