Windshield: Service and Repair
WINDSHIELD GLASSREMOVAL
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
2. REMOVE FRONT DOOR SCUFF PLATE LH
3. REMOVE FRONT DOOR SCUFF PLATE RH
4. REMOVE COWL SIDE TRIM BOARD LH
5. REMOVE COWL SIDE TRIM BOARD RH
6. REMOVE FRONT DOOR OPENING TRIM LH
a. Partially remove the front door opening trim weatherstrip LH so that the front pillar garnish LH can be removed.
7. REMOVE FRONT DOOR OPENING TRIM RH
HINT: Use the same procedures described for the LH side.
8. REMOVE FRONT PILLAR GARNISH CORNER PIECE LH
9. REMOVE FRONT PILLAR GARNISH CORNER PIECE RH
10. REMOVE FRONT PILLAR GARNISH LH
11. REMOVE FRONT PILLAR GARNISH RH
12. REMOVE VISOR ASSEMBLY LH
13. REMOVE VISOR ASSEMBLY RH
14. REMOVE VISOR HOLDER
15. REMOVE ASSIST GRIP COVER
16. REMOVE ASSIST GRIP SUB-ASSEMBLY
17. REMOVE MAP LIGHT ASSEMBLY
18. REMOVE ROOF HEADLINING ASSEMBLY
HINT: It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining.
a. Partially remove the roof headlining.
19. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)
20. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)
21. REMOVE HOOD TO COWL TOP SEAL
22. REMOVE FRONT WIPER ARM HEAD CAP
23. REMOVE FRONT WIPER ARM LH
24. REMOVE FRONT WIPER ARM RH
25. REMOVE COWL TOP VENTILATOR LOUVER LH
26. REMOVE COWL TOP VENTILATOR LOUVER RH
27. REMOVE WINDSHIELD MOULDING OUTSIDE
a. Using a knife, cut off the moulding as shown in the illustration.
NOTE: Be careful not to damage the vehicle body.
b. Remove the remaining moulding.
HINT: Make a partial cut in the moulding. Then pull and remove it by hand.
28. REMOVE WINDSHIELD GLASS
a. Apply protective tape to the outer surface of the vehicle body to prevent scratches.
b. From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.
c. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
NOTE:
- When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
- To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.
d. Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.
HINT: Matchmarks do not need to be placed if not reusing the glass.
e. Cut through the adhesive by pulling the piano wire around the glass.
NOTE: Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.
f. Disengage the stoppers.
g. Using suction cups, remove the glass.
29. CLEAN WINDSHIELD GLASS
a. Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.
b. Clean the outer edges of the glass with white gasoline.
NOTE: Do not touch the glass surface after cleaning it. Even if using new glass, clean it with white gasoline.
30. CLEAN VEHICLE BODY
a. Clean and shape the contact surface of the vehicle body.
1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
HINT: Leave as much adhesive on the vehicle body as possible.
NOTE: Be careful not to damage the vehicle body.
b. Clean the contact surface of the vehicle body with cleaner.
HINT: Even if all the adhesive has been removed, clean the vehicle body.
INSTALLATION
1. INSTALL NO. 2 WINDSHIELD GLASS STOPPER
a. Apply Primer G to the glass where the stoppers will be installed.
NOTE:
- Allow the primer to dry for 3 minutes or more.
- Throw away any leftover primer.
- Do not apply too much primer.
b. Install 2 new stoppers onto the glass as shown in the illustration.
2. INSTALL NO. 1 WINDSHIELD GLASS STOPPER
a. Install 2 new stoppers to the vehicle body as shown in the illustration.
3. INSTALL WINDOW GLASS ADHESIVE DAM
a. Apply Primer G to the glass where the glass adhesive dams will be installed.
NOTE:
- Allow the primer to dry for 3 minutes or more.
- Throw away any leftover primer.
- Do not apply too much primer.
b. Remove the peeling paper from the adhesive part of the dam. Install the dam (adhesive side) to the glass (Primer G area), but exclude the spacer area A as shown in the illustration.
4. INSTALL WINDSHIELD GLASS
a. Position the glass.
1. Using suction cups, place the glass in the correct position.
2. Check that the entire contact surface of the glass rim is perfectly even.
3. Place matchmarks on the glass and vehicle body on the locations indicated in the illustration.
HINT:
- Placing matchmarks is only necessary when installing new glass. If it is the reused glass, matchmarks should already be present.
- When reusing the glass, check and correct the matchmark positions.
NOTE: Check that the stoppers are attached to the vehicle body correctly.
4. Using suction cups, remove the glass.
b. Using a brush, apply Primer M to the exposed part of the vehicle body.
NOTE:
- Allow the primer to dry for 3 minutes or more.
- Do not apply primer to the adhesive.
- Throw away any leftover primer.
- Do not apply too much primer.
c. Using a brush or sponge, apply Primer G to the contact surface of the glass.
HINT: If the primer is applied to an area that is not specified, apply white gasoline to a clean cloth and wipe off the excess primer.
NOTE:
- Allow the primer to dry for 3 minutes or more.
- Throw away any leftover primer.
- Do not apply too much primer.
d. Apply adhesive to the glass.
Adhesive: Toyota Genuine Windshield Glass Adhesive or Equivalent
1. Cut off the tip of the cartridge nozzle as shown in the illustration.
HINT: After cutting off the tip, use all adhesive within the time written in the table.
2. Load the sealer gun with the cartridge.
3. Apply adhesive to the glass as shown in the illustration.
e. Install the glass to the vehicle body.
1. Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.
2. Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.
NOTE:
- Check that the stoppers are attached to the vehicle body correctly.
- Check that the vehicle body and glass have a small gap between them.
3. Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.
5. INSTALL WINDSHIELD MOULDING OUTSIDE
a. Using a brush or sponge, apply Primer G to the glass where a new moulding will be installed.
NOTE:
- Allow the primer to dry for 3 minutes or more.
- Throw away any leftover primer.
- Do not apply too much primer.
b. Align the moulding's marks with glass notches and install the moulding before the adhesive dries.
NOTE: Do not drive the vehicle for the amount of time written in the table.
6. INSTALL COWL TOP VENTILATOR LOUVER RH
7. INSTALL COWL TOP VENTILATOR LOUVER LH
8. INSTALL FRONT WIPER ARM LH
9. INSTALL FRONT WIPER ARM RH
10. INSTALL FRONT WIPER ARM HEAD CAP
11. INSTALL HOOD TO COWL TOP SEAL
12. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)
13. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)
14. INSTALL ROOF HEADLINING ASSEMBLY
15. INSTALL MAP LIGHT ASSEMBLY
16. INSTALL ASSIST GRIP SUB-ASSEMBLY
17. INSTALL ASSIST GRIP COVER
18. INSTALL VISOR HOLDER
19. INSTALL VISOR ASSEMBLY LH
20. INSTALL VISOR ASSEMBLY RH
21. INSTALL FRONT PILLAR GARNISH LH
22. INSTALL FRONT PILLAR GARNISH RH
23. INSTALL FRONT PILLAR GARNISH CORNER PIECE LH
24. INSTALL FRONT PILLAR GARNISH CORNER PIECE RH
25. INSTALL FRONT DOOR OPENING TRIM LH
26. INSTALL FRONT DOOR OPENING TRIM RH
27. INSTALL COWL SIDE TRIM BOARD LH
28. REMOVE COWL SIDE TRIM BOARD RH
29. REMOVE FRONT DOOR SCUFF PLATE LH
30. INSTALL FRONT DOOR SCUFF PLATE RH
31. CHECK FOR LEAKS AND REPAIR
a. Conduct a leak test after the adhesive has completely hardened.
b. Seal any leaks with auto glass sealer.
32. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
33. PERFORM INITIALIZATION
a. Perform initialization.
NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.