Operation CHARM: Car repair manuals for everyone.

Troubleshooting Mirror System

Checking Mirror Control System

1. Store mirror position into memory with position key 1.

2. Detach mirror control.

The mirror control unit is mounted on the side wall in the driver's side footwell beside the ABS control unit.

Checking Mirror Control Switches

3. Disconnect plug 1.

4. Set mirror selector switch to driver side mirror.

5. Connect Voltmeter (+) to terminal 1 and (-) to terminal 2 of plug receptacle.

Push mirror adjuster switch to left.

Reading: Battery voltage.

Connect Voltmeter (-) to terminal 1 and (+) to terminal 2.

Push mirror adjuster switch to right.

Reading: Battery voltage.

6. Connect Voltmeter (+) to terminal 5 and (-) to terminal 2.

Push mirror adjuster switch up.

Reading: Battery voltage.

Connect Voltmeter (-) to terminal 5 and (+) to terminal 2.

Push mirror adjuster switch down.

Reading: Battery voltage.

7. Set mirror selector switch to passenger side mirror.

8. Connect Voltmeter (+) to terminal 3 and (-) to terminal 2.

Push mirror adjuster switch to left.

Reading: Battery voltage.
Connect Voltmeter (-) to terminal 3 and (+) to terminal 2.

Push mirror adjuster switch to right.

Reading: Battery voltage.

9. Connect Voltmeter (+) to terminal 4 and (-) to terminal 2.

Push mirror adjuster switch up.

Reading: Battery voltage.

Connect Voltmeter (-) to terminal 4 and (+) to terminal 2.

Push mirror adjuster switch down.

Reading: Battery voltage.

If values are not reached, check wiring and mirror selector and adjuster switches.

Reconnect plug 1.

Checking Memory Switch and Power Supply

10. Disconnect plug 2 from mirror control unit.

Disconnect plug 9 from seat memory control unit.

Connect ohmmeter to ground and terminal 1 of plug receptacle.

Press position key 1.

Reading: 0-2 ohms.

Press position key 2.

Reading: approximately 240 ohms.

Press position key 3.

Reading: approximately 820 ohms.

Reconnect plug 9 on seat memory control unit.

11. Connect ohmmeter to ground and terminal 4.

Press memory key.

Reading: 0-2 ohms.
Checking Memory Switch and Power Supply (continued)

12. Connect Voltmeter (+) to terminal 3 and (-) to terminal 5.

Press position key 1.

Reading: Battery voltage.

Reconnect plug 2 on mirror control unit.

If values are not reached check wiring and memory switch.

NOTE: Voltage is applied for approximately 30 seconds after position keys are pressed.


Checking Mirror Control Unit

13. Open plug cover of plug 3.

Leave plug connected.

14. Connect Voltmeter (-) to terminal 1 and (+) to terminal 2.

Press position key 1.

Reading: approximately 4.7 volts

15. Connect Voltmeter (-) to terminal 3 and (+) to terminal 4.

Press position key 1.

Reading: approximately 4.7 volts.

16. Connect Voltmeter (+) to terminal 4 and (-) to terminal 5.

Press position key 1.

Reading: 0.3-4.5 volts.

17. Connect Voltmeter (+) to terminal 4 and (-) to terminal 7.

Press position key 1.

Reading: 0.3-4.5 volts.
18. Connect Voltmeter (+) to terminal 2 and (-) to terminal 9.

Press position key 1.

Reading: 0.3-4.5 volts.

19. Connect Voltmeter (+) to terminal 2 and (-) to terminal 11.

Press position key 1.

Reading: 0.3-4.5 volts.

NOTE: Voltage is applied for approximately 30 seconds after position keys are pressed.

20. Set mirror selector switch to driver side mirror.

21. Connect Voltmeter (+) to terminal 6 and (-) to terminal 13.

Push mirror adjuster switch up.

Reading: approximate battery voltage.

22. Connect Voltmeter (-) to terminal 6 and (+) to terminal 13.

Push mirror adjuster switch down.

Reading: approximate battery voltage.

23. Connect Voltmeter (-) to terminal 13 and (+) to terminal 14.

Push mirror selector switch to left.

Reading: approximate battery voltage.

24. Connect Voltmeter (+) to terminal 13 and (-) to terminal 14.

Push mirror adjuster switch to right.

Reading: approximate battery voltage.

25. Set mirror selector switch to passenger side mirror.

26. Connect Voltmeter (-) to terminal 8 and (+) to terminal 10.

Push mirror adjuster switch up.

Reading: approximate battery voltage.
Checking Mirror Control Unit (continued)


27. Connect Voltmeter (+) to terminal 8 and (-) to terminal 10.

Push mirror adjuster switch down.

Reading: approximate battery voltage.

28. Connect Voltmeter (-) to terminal 8 and (+) to terminal 12.

Push mirror adjuster switch to left.

Reading: approximate battery voltage.

29. Connect Voltmeter (+) to terminal 8 and (-) to terminal 12.

Push mirror adjuster switch to right.

Reading: approximate battery voltage.

If values are not reached, check wiring.

If wiring is okay, replace mirror control unit. Reinstall plug cover.

NOTE: approximate battery voltage can be somewhat lower than actual battery voltage.
Checking Memory Switch and Wiring

1. Remove memory switch panel.

2. Disconnect plug.

3. Connect Voltmeter (+) to terminal 1 and (-) to terminal 4 of plug receptacle in harness.

Reading: Battery voltage.

If no reading, check wiring to seat control unit.

4. Connect ohmmeter to terminal 1 and terminal 4 of disconnected switch.

Reading: infinite ohms.

Press key 1.

Reading: approximately 0 ohms.

Press key 2.

Reading: approximately 240 ohms.

Press key 2.

Reading: approximately 820 ohms.

5. Connect ohmmeter to terminal 2 and terminal 4 of disconnected switch.

Reading: infinite ohms. Press memory key.

Reading: approximately 0 ohms.

If values are not reached, replace memory switch.

Reinstall seat and control units.