Operation CHARM: Car repair manuals for everyone.

Intake Manifold Replacement

Intake Manifold Replacement

Removal Procedure





1. Disconnect the negative battery cable.
2. Remove the air cleaner intake duct.
3. Partially drain the engine cooling system.
4. Remove the fuel injector sight shield.
5. Remove the throttle and the cruise control cables with the mounting bracket from the throttle body.
6. Remove the throttle body coolant hoses from the throttle body.





7. Remove the fuel lines from the fuel rail.





8. Remove the fuel vapor line from the EVAP canister purge solenoid.





9. Remove the brake booster vacuum hose from the brake booster.
10. Remove the A/C vacuum hose from the intake manifold.
11. Remove the surge tank inlet pipe retainer from the fuel injector rail.
12. Disconnect the electrical connectors from the following components:
- Fuel injectors
- Throttle position (TP) sensor
- Idle air control (IAC) valve
- EVAP canister purge solenoid
- Manifold absolute pressure (MAP) sensor
13. Remove the engine wiring harness channel bolts from the camshaft covers.
14. Remove and set aside the engine wiring harness and channel.





15. Remove the fuel pressure regulator vacuum tube (1) from the regulator (2) and the throttle body (3)





16. Remove the PCV valve and the vacuum hoses (1, 2) from the camshaft covers and the intake manifold.





17. Remove the EGR valve outlet pipe bolts from the intake manifold and the water crossover.
18. Remove the EGR valve outlet pipe.
19. Remove the fuel rail assembly.





20. Remove the intake manifold bolts.





21. Remove the throttle body coolant hose from the water crossover feed tube (1).





22. Remove the intake manifold.

Important: If you are replacing the intake manifold perform the following steps.

23. Disassemble the intake manifold.
24. Clean and inspect the intake manifold.
25. Assemble the intake manifold.

Installation Procedure





1. Install the intake manifold.





2. Install the throttle body heater hose to the water crossover feed tube (1).
3. Install the hose clamp.

Notice: Refer to Fastener Notice in Service Precautions.

Important: Tighten the intake manifold bolts in circular pattern starting from the center and moving outward.





4. Install the intake manifold bolts.
- Tighten the bolts to 7 Nm (62 inch lbs.).
5. Inspect the fuel injector O-rings (2) for misalignment or damage. Replace the O-rings if necessary.
6. Install the fuel rail assembly.





7. Install the EGR outlet pipe.
8. Install the EGR outlet pipe to intake manifold bolts.
- Tighten the bolts to 10 Nm (89 inch lbs.).
9. Install the EGR outlet pipe to water crossover bolts.
- Tighten the bolts to 24 Nm (18 ft. lbs.).





10. Install the vacuum hoses (1,2) and the PCV valve to the camshaft covers and the intake manifold.





11. Install the brake booster vacuum hose to the brake booster.





12. Install the fuel pressure regulator vacuum tube (1) to the regulator (2) and the throttle body (3).
13. Install the A/C vacuum hose to the intake manifold.
14. Install the engine wiring harness and channel.
15. Install the engine wiring harness channel bolts to the camshaft covers.
- Tighten the bolts to 10 Nm (89 inch lbs.).
16. Connect the surge tank inlet pipe retainer to the fuel injector rail.
17. Connect the electrical connectors to the following components:
- Throttle position (TP) sensor
- Idle air control (IAC) valve
- EVAP canister purge solenoid
- Manifold absolute pressure (MAP) sensor
- Fuel injectors
18. Install the throttle body coolant hoses to the throttle body.
19. Install the throttle and the cruise control cables with the mounting bracket to the throttle body.





20. Install the fuel lines to the fuel rail.





21. Connect the fuel vapor line to the EVAP canister purge solenoid.
22. Install the air cleaner intake duct.





23. Install the fuel injector sight shield.
24. Fill the cooling system.
25. Connect the negative battery cable.