Operation CHARM: Car repair manuals for everyone.

Output Devices -- Outline

OUTPUT DEVICE
Accelerated Warm-up System Solenoid Valve

- If the solenoid valve or circuit has an open or short, Trouble Code No. 38 is output.
- If the circuit is open, the fast idle speed just after engine starting will not exceed 2,000 rpm.
- If the circuit is shorted, the idle speed will be increased and then hunted at the specified speed (approx. 1500 rpm after Warm-up).

A/C Relay
- If the circuit is open, the air conditioner (Magnetic Clutch) will not operate.
- If the circuit is shorted, the air conditioner will constantly operate when blower is on, causing rough idle.

Air Pump Relay
- If the relay or circuit has an open or short, Trouble Code No. 54 is output.
- If the circuit is short, air pump will always operate, causing Three-way Catalytic Converter melted.
- If the circuit is open, the air pump will never operate, causing rough idle.

Charge Control Solenoid Valve
- If the Solenoid Valve Or circuit has an open or short, Trouble Code No. 45 is output.
- In the above conditions, the ECM fixes the ignition timing and fuel injection amount, causing poor acceleration and lack of power.

Charge Relief Solenoid Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 46 is output.
- If the circuit is open, the charge relief valve will always open, causing poor acceleration.
- If the circuit is shorted, the charge relief valve will always closed, causing momentarily intake air noise on acceleration.

Double Throttle Control Solenoid Valve
- If the Solenoid Valve Or circuit has an open or short, Trouble Code No. 50 is output.
- If the circuit is open, the double throttle valve will always closed, causing poor acceleration and lack of power.
- If the circuit is shorted, the double throttle valve will always open, causing hesitation when the engine is cold.

Fan Relay
- If the circuit is shorted, the coolant fan will always operate while the ignition switch on.
- If the circuit is open, the coolant fan will not operate until the engine temperature exceeds 1O8°C (226°F).

FEN Terminal (Data Link Connector)
- If The circuit between the data link connector and E/L unit is open, the self-diagnosis checker buzzer will not sound during the Trouble Code check.
- If the circuit between ECM 1 F terminal and E/L unit is open, the Self-Diagnosis Checker buzzer will constantly sound during the Trouble Code check.
- If the circuit is shorted, Code "88" Will keep flashing and the buzzer will continue sounding (Self-Diagnosis Checker), preventing a Trouble Code check.

Fuel Injector
- If a secondary injector or circuit has an open or short, Trouble Code No. 71 (Front) or 73 (Rear) is output, causing poor acceleration and lack of engine power.
- If a primary fuel injector or circuit has an open, engine will stall and will not start.

Fuel Pump Relay
- If the circuit is open, the engine will not start.
- If The circuit is shorted, the fuel pump will operate whenever the ignition switch is on.

Fuel Pump Relay (speed)
- If The relay or circuit has an open or short, Trouble Code No. 51 is output.
- If the circuit is open, engine will hesitate or engine power will lack.

Idle Air Control Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 34 is output.
- If The circuit is open, the valve will always closed throttle position, causing rough idle and hard starting.
- If the circuit is shorted, the valve will always wide open throttle, causing high idle speed. (After Warm-up, engine hunts at approx. 1500 rpm.)

Ignition Control Module
- If a trailing ignition control module or circuit has an open or short, idle speed will be slightly decreased and poor acceleration will be cased.
- If the leading ignition control module or circuit has an open or short, hard starting and rough idle will be caused.

MEN Terminal (Data Link Connector)
- If the circuit is open, the monitor lamp will not illuminate.
- If the circuit is shorted, the monitor lamp will stay on.

Metering Oil Pump
- If the pump or circuit has an open or short, Trouble Code No. 26 and 27 are output.
- In the above conditions, ECM fixes ignition timing and fuel injection amount, causing engine poor acceleration.

Secondary Air Bypass Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 31 is output.
- If the circuit is open, no symptom will be noticed.
- If the circuit is shorted solenoid valve will be always open and CO and HC will be increased.

Secondary Air Switching Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 32 is output.
- If the circuit is open, no symptom will be noticed.
- If the circuit is shorted, rough idle will result.

Port Air Bypass Solenoid Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 33 is output.
- In the above conditions, no symptom will be noticed.

Pressure Regulator Control Solenoid Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 25 is output.
- If the circuit is open, hard starting may result when the engine is hot.
- If the circuit is shorted, fuel pressure will always be approx. 280 kPa (2.9 kgf/cm2, 41 psi) and no symptom will be noticed.

Purge Solenoid Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 40 is output.
- If the circuit is open, no symptom will be noticed.
- If the circuit is shorted, the engine stalls at low speed.

Relief 2 Solenoid Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 39 is output.
- If the circuit is open, no symptom will be noticed.
- If the circuit is shorted, secondary air noise will be heard while the air pump operates.

Split Air Bypass Solenoid Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 30 is output.
- In the above conditions, no symptom will be produced.

Turbo Control 1, Turbo Control 2 Solenoid Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 44 is output.
- If the circuit is open, the turbo control valve will not open, causing poor acceleration and lack of power.
- If the circuit is shorted, turbo control valve will open earlier on acceleration, causing poor acceleration.

Turbo Precontrol Solenoid Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 42 is output.
- If the circuit is open, the precontrol valve will open earlier, causing slightly hesitation and poor acceleration.
- If the circuit is short, precontrol valve will never open, causing hesitation and poor acceleration.

Wastegate Control Solenoid Valve
- If the solenoid valve or circuit has an open or short, Trouble Code No. 43 is output.
- If the circuit is open, wastegate valve will open earlier, causing poor acceleration and lack of power.
- If the circuit is shorted, wastegate valve will not open easily and no symptom will be noticed. (To prevent engine damage, the overboost fuel cut will be operated.)