Operation CHARM: Car repair manuals for everyone.

Disassembly




1. 5th/Reverse shift rod end
2. 3rd/4th shift rod end
3. 1st/2nd shift rod end
4. Bearing housing
5. Snap ring
6. Thrust washer
7. C-washers
8. Retaining ring
9. Mainshaft rear bearing
10. C-washers and retaining ring
11. Locknut
12. Countershaft rear bearing
13. Counter 5th gear
14. Spacer
15. Set bolt and washer
16. Center housing
17. Oil guide
18. Blind cover
19. Cap plug, spring, and detent ball
20. Thrust lock washer
21. Steel ball
22. Bearing Inspect for damage
23. 5th gear
24. Retaining ring
25. Synchronizer ring (5th)
26. Retaining ring
27. 5th/Reverse shift rod
28. Spring
29. 5th/Reverse shift fork
30. Interlock pin (large)
31. 3rd/4th shift rod
32. Interlock pin (small)
33. Interlock pin (large)
34. 1st/2nd shift rod
35. Thrust washer
36. Reverse idler gear shaft
37. Reverse idler gear
38. Thrust washer
39. Counter reverse gear
40. Locknut
41. 5th/Reverse clutch hub assembly
42. Synchronizer ring
43. Reverse gear
44. Bearing
45. Bearing race
46. Thrust washer
47. Bearing cover
48. Oil guide

Disassemble in the order shown in the image referring to Disassembly Note.




Disassembly note Bearing housing

CAUTION: Using metal tools to remove the bearing housing could cause severe damage to its machined surfaces.

Hit down and outward on the bearing housing with a plastic hammer to remove.




Mainshaft rear bearing

CAUTION: The front and rear C-washers may have different thicknesses.

1. Remove the snap ring, washer, retaining ring, and rear C-washers.
2. Remove the mainshaft rear bearing by using the SST.
3. Remove the retaining ring and the front C-washers.




Locknut and countershaft rear bearing
1. Shift the 1st/2nd shift rod to 1st gear.

CAUTION:
- Do not reuse the locknut.
- Do not scratch or damage the countershaft.

2. Uncrimp the tab of the locknut.
3. Hold the mainshaft by using the SST and a vise.
4. Remove the locknut.




5. Remove the countershaft rear bearing by using the SST.




Center housing
1. Remove the set bolt and washer from the center housing.

NOTE: If the center housing is difficult to remove, tap around the edge of the center housing with a plastic hammer.

2. Remove the center housing.




5th/Reverse shift rod
1. Remove the three cap plugs, packings, detent balls, and springs.




2. Drive the roll pin from the 5th/Reverse shift fork.




3. Pull the retaining ring from the 5th/Reverse shift rod.
4. Slide the 5th/Reverse shift rod out of the transmission case, and remove the spring.




1st/2nd and 3rd/4th shift rods
1. Shift the transmission into 4th gear to gain access to the roll pin. Drive the roll pin from the 3rd/4th shift fork.
2. Slide the 3rd/4th shift rod and interlock pin (small) out from the rear of the transmission case.
3. Drive the roll pin from the 1st/2nd shift fork. Slide the 1st/2nd shift rod out from the rear of the transmission case, and remove the interlock pin (large).




Locknut
1. Uncrimp the tab of the locknut.
2. Shift into 1st and 4th gears to lock the rotation of the mainshaft.

CAUTION: Do not reuse the locknut.




3. Remove the locknut by using the SST.




5th/Reverse clutch hub assembly
1. Remove the bearing cover installation bolts.
2. Attach the SST to the bearing cover and remove the assembly, which consists of the following parts:
- 5th/Reverse clutch hub assembly
- Synchronizer ring
- Needle bearing
- Bearing race
- Reverse gear
- Thrust washer