Operation CHARM: Car repair manuals for everyone.

Campaign - Engine Intake Air Breather Pipe Replacement

03-043

July 8, 2009

Applies To:
See VEHICLES AFFECTED

Product Update: Intake Air Breather Pipe

(Supersedes 03-043, dated November 9, 2004, to revise the information marked by the black bars and asterisks)

*REVISION SUMMARY
Under PARTS INFORMATION, the Intake Air Breather
Pipe Kit was changed to individual parts.*

BACKGROUND

The hose on the intake air breather pipe can cause the pipe to separate from the airflow chamber during heavy throttle applications. If this happens on a SULEV model, it causes the MIL to come on with DTC P0171 (fuel supply system too lean).





VEHICLES AFFECTED

Not all vehicles within the VIN ranges are affected by this product update. Before beginning work on a vehicle, verify its eligibility by checking at least one of these items:

^ The customer has a notification letter.

^ The vehicle is shown on your campaign responsibility report.

^ The vehicle is shown as eligible on an iN VIN status inquiry.

In addition to the bulleted verification items, check for a punch mark above the seventh character of the engine compartment VIN. A punch mark in that location means this campaign has already been done.

If any affected vehicles are in your new or used vehicle inventory, repair them as described in this service bulletin.

CUSTOMER NOTIFICATION





All owners of affected vehicles will be sent a notification of this product update. The customer notification may also contain information on other product updates. An example of the customer notification for this intake air breather pipe product update is at the end of this service bulletin.

CORRECTIVE ACTION

Replace the intake air breather pipe and hose. (The hose length has been increased 10 mm, and there is a barb on the end of the air breather pipe to help retain the hose.)

TOOL INFORMATION

You need two hose-pinching pliers to complete this repair. If you do not have these tools, you can order them from the Honda Tool and Equipment Program by. Ask for T/N YA965.

PARTS INFORMATION

*Breather Pipe: P/N 17137-RAA-A01, H/C 7501836

Breather Pipe Hose (Tube):
P/N 17153-RM-A01, H/C 7501844*

WARRANTY CLAIM INFORMATION

Operation Number: 122125

Flat Rate Time: 0.2 hour

Failed Part: P/N 17137-RAA-A00
H/C 7244767

Defect Code: 5CB00

Symptom Code: P0100

Template ID: 03-043B

Skill Level: Repair Technician

REPAIR PROCEDURE

1. Use two hose-pinching pliers (T/N YA965) to pinch off the two coolant hoses leading to the breather pipe.





[NOTICE]
Do not use vise grips; they would damage the coolant hoses. To avoid hose puncture, make sure you place the hose-pinching pliers at least 1.5 inches from the end of the hose.

2. Release the clamps on the intake air breather pipe hose and the airflow chamber.





3. Remove and discard the breather pipe and the breather pipe hose. Retain all hose clamps.





4. Install the new breather pipe and breather pipe hose. Use the original hose clamps to secure the breather pipe to the airflow chamber and the breather pipe hose to the valve cover.





NOTE:
The breather pipe hose has a large end and a small end. Make sure you attach the large end to the valve cover with the large hose clamp, and the small end to the breather pipe with the small hose clamp.

5. Install the coolant hoses and hose clamps, then remove the hose-pinching pliers.

6. Wipe off any excess coolant that may have spilled on the engine.





7. Center-punch a completion mark above the seventh character of the engine compartment VIN.

8. For California residents: Fill out and give to your customer a Vehicle Emission Recall - Proof of Correction certificate. On the certificate, write down P01 as the recall number. Advise your customer to keep this certificate as proof that the product update was completed. They will need to submit this certificate to the DMV if the DMV requests it. A supply of these salmon-colored certificates was sent to your service manager. If you need more, use reorder number Y0657.





Disclaimer