Combination Switch: Description and Operation
Left( Lighting) Multi-function Switch:
The left (lighting) multi-function switch is secured to the left side of the multi-function switch mounting housing at the top of the steering column, just below the steering wheel. The only visible component of the left multi-function switch is the control stalk that extends through a dedicated opening in the left side of the steering column shrouds. The remainder of the left multi-function switch is concealed beneath the steering column shrouds. The switch is secured to the multi-function switch mounting housing near the top of the steering column by two screws.
The control stalk has a control knob on its end with a knurled face to allow it to be easily rotated. Just below the control knob is a knurled control sleeve. The left multi-function switch is the primary control for the interior and exterior lighting systems, and contains switches and circuitry to provide signals to the Body Control Module (BCM).
The left (lighting) multi-function switch cannot be adjusted or repaired. If any function of the switch is faulty, or if the switch is damaged, the entire switch unit must be replaced.
A single connector with eleven terminal pins is located on the back of the switch housing and connects the switch to the vehicle electrical system. The left multi-function switch supports the following exterior lighting functions:
- Auto Headlamps
- Front Fog Lamps
- Headlamps
- Headlamp Beam Selection
- Headlamp Optical Horn
- Park Lamps
- Turn Signal Control
The left multi-function switch also supports the following interior lighting functions:
- Panel Lamps Dimming
- Interior Lamps Defeat
- Interior Lamps On
- Parade Mode
The left multi-function switch uses a combination of resistor multiplexed and conventionally switched outputs to control the many functions and features it provides using a minimal number of hard wired circuits. The switch is grounded to the chassis. The left multi-function switch operates to control the many exterior lighting functions and features it provides:
- Auto Headlamps - The automatic headlamps feature is provided by the Body Control Module (BCM), which monitors an input from a photodiode sensor located in the Electrochromatic Mirror (ECM) to detect ambient light levels whenever the ignition switch is in the ON position. Based upon the multiplexed input from the left multi-function switch and the input of the photodiode sensor, the BCM provides a message to the IPM to illuminate or extinguish all exterior lighting.
- Front Fog Lamps - The Body Control Module (BCM) monitors the left multi-function switch then, based upon that switched ground input, provides a message to the IPM to illuminate or extinguish the front fog lamps.
- Headlamps - The Body Control Module (BCM) monitors the left multi-function switch then, provides a message to the IPM to illuminate or extinguish the headlamps.
- Headlamp Beam Selection - The Body Control Module (BCM) monitors the left multi-function switch then, based upon that switched ground input, provides a message to the IPM to activate the selected headlamp beam.
- Headlamp Optical Horn - The Body Control Module (BCM) monitors the left multi-function switch then, based upon that switched ground input, provides a message to the IPM to activate the headlamp high beams.
- Park Lamps - The Body Control Module (BCM) monitors the left multi-function switch then, based upon that multiplexed input, provides a message to the IPM to illuminate or extinguish the parking lamps.
- Turn Signal Control - The left multi-function switch control stalk actuates the turn signal switch. The Body Control Module (BCM) monitors the left multi-function switch then, based upon that multiplexed input, provides a variable voltage output to control the lighting of the turn signals.
The left multi-function switch operates to control the many interior lighting functions and features it provides:
- Panel Lamps Dimming - The Body Control Module (BCM) monitors the left multi-function switch then, based upon that multiplexed input, provides a variable voltage output through several panel lamps driver circuits to control the lighting of many incandescent panel lamps. The BCM also sends panel lamps dimming messages over the Programmable Communications Interface (PCI) data bus to other modules to control Display lighting levels in those modules.
- Interior Lamps Defeat - The Body Control Module (BCM) monitors the left multi-function switch then, based upon that multiplexed input, internally disables the function the BCM normally provides to control the illumination of the interior lamps.
- Interior Lamps On - The Body Control Module (BCM) monitors the left multi-function switch then, based upon that multiplexed input, provides a control output to activate all of the interior lamp circuits.
- Parade Mode - The Body Control Module (BCM) monitors the left multi-function switch then, based upon that multiplexed input, provides a voltage output through several panel lamps driver circuits to control the lighting of many incandescent panel lamps. The BCM also sends panel lamps dimming messages over the Programmable Communications Interface (PCI) data bus to other modules on the bus to control lighting levels in those modules.