Heated Seat System
FRONT SEART HEATED SEAT SYSTEM DIAGNOSISIn order to obtain conclusive testing of the front seat heated seat system, the Programmable Communications Interface (PCI) data bus circuit must be checked.
The most reliable, efficient, and accurate means to diagnose the front seat heated seat system requires the use of a DRB III(R) scan tool and the Service and Body Diagnostic Manuals. The DRB III(R) scan tool can provide vital information to the technician trying to find a problem with the heated seat system. Diagnostic logic is built into the memory heated seat adjustable pedal module and both door modules to help the person trying to locate the problem by the most efficient means possible. Anytime a problem is suspected, a DRB III(R) scan tool should be obtained and used to retrieve any stored fault codes in the memory heated seat adjustable pedal module and door modules. If the front heated seat lights blink the MHSAPM did not respond to the door modules command to turn on the heated seats.
If diagnostic fault codes are present in the module, record them on a piece of paper immediately before proceeding any further. Then, use these fault codes to identify the problem by verifying the fault code. Example, If the module records "DRIVER SEAT HEAT OUTPUT OPEN" fault code, locate the diagnostic procedure for this code in the appropriate Body Diagnostic Manual and follow the flow chart until the specific problem is located and resolved. Once the problem is thought to be corrected, erase the stored fault code using the DRB III(R) scan tool and verify correct system operation. If the front seat heated seat system is functioning correctly, verify that there are no other stored codes in the module and return the vehicle to service.
If the fault code could not be verified, such as not finding anything wrong when following the diagnostic flow chart in the Body Diagnostic Manual. This is a good indication that a INTERMITTENT problem may be present. You must than attempt to find the intermittent problem, such as moving the heating element within the seat while testing continuity or wiggling the wire harness's/electrical connectors under the seat while testing continuity. Always, eliminate all other potential problems before attempting to replace the memory heated seat adjustable pedal module.
For complete circuit wiring diagrams, refer to Wiring.
PRELIMINARY TEST
Before testing the individual components in the heated seat system, check the following:
- Using the DRB III(R) scan tool, check the memory heated seat adjustable pedal module (MHSAPM) for any stored fault codes. Record these codes on paper for reference and resolve using the appropriate Body Diagnostic Manual.
- Check the vehicles battery open-circuit voltage and charging system performance. If the vehicles electrical system is defective or weak it may not be suppling sufficient energy to operate the heated seat system.
- If the heated seat switch backlighting does not light with the ignition switch in the On position, check the fused ignition switch fuse in the integrated power module. If OK, refer to Heated Seat Switch Diagnosis and Testing. If not OK, repair the shorted circuit or component as required and replace the faulty fuse or repair the open ground circuit as required.
- If the heated seat switch HI/LO LED indicators do not light with the ignition switch in the On position and the heated seat switch in the Low or High position, check the fused ignition switch fuse in the integrated power module. If OK, refer to Heated Seat Switch Diagnosis and Testing. If not OK, repair the shorted circuit or component as required and replace the faulty fuse.
2ND ROW HEATED SEAT SYSTEM DIAGNOSIS
Heated Seat System Self-Diagnosis:
The 2nd row heated seat system is capable of performing some self-diagnostics. The following table depicts the various monitored faults which will be reported to the vehicle operator or technician by flashing the individual heated seat switch Light Emitting Diode (LED) indicator lamps. Refer to the HEATED SEAT SYSTEM SELF-DIAGNOSIS table below for failure identification. The left side heated seat switch indicator lamps will flash if a failure occurs in the left rear heated seat, and the right side heated seat switch indicator lamps will flash for a right rear heated seat failure. If a monitored heated seat system fault occurs, the switch indicator lamps will flash at a pulse rate of one-half second on, followed by one-half second off for a duration of one minute after the switch for the faulty heated seat is depressed in either the Low or High direction. This process will repeat every time the faulty heated seat switch is actuated until the problem has been corrected.
Diagnostic logic is built into the 2nd row heated seat module to help the person trying to locate the problem by the most efficient means possible. Anytime a problem is suspected, locate the diagnosis and testing procedure for the component in question and follow the steps until the specific problem is located and resolved. Always eliminate problems in this order; sensors, wiring, element, switch, switch wiring, memory heated seat adjustable pedal module and corresponding door module. Once the problem is thought to be corrected, verify correct system operation. If the heated seat system is functioning correctly return the vehicle to service.
If a problem could not be verified such as not finding anything wrong when following the diagnostic procedure, this is a good indication that a INTERMITTENT problem may be present. You must then attempt to find the intermittent problem, such as moving the heating element within the seat while testing continuity or wiggling the wire harness's/electrical connectors under the seat while testing continuity.