Engine Oil Pressure: Testing and Inspection
Oil Pressure Diagnosis and Testing (L98, LS2, L76, L77)
Special Tools
* EN-21867 - Pressure Gauge
* EN-21867-16 - Oil Pressure Adapter
For equivalent regional tools, refer to Special Tools Special Tools.
1. With the vehicle on a level surface, run the vehicle for a few minutes, allow adequate drain down time, 2 - 3 minutes, and measure the oil level.
2. If required, add the recommended grade engine oil and fill the crankcase until the oil level measures full on the oil level indicator.
3. Run the engine briefly, 10-15 seconds, and verify low or no oil pressure on the vehicle gauge or light.
4. Listen for a noisy valve train or a knocking noise.
5. Inspect for the following conditions:
* Oil diluted by water or glycol anti freeze
* Foamy oil
6. Remove the oil pressure sensor (1).
7. Install the EN-21867-16 - adapter (2) and EN-21867 - pressure gauge (1), or equivalent.
8. Run the engine until the engine reaches normal operating temperature and measure the engine oil pressure.
9. Compare the readings to Engine Mechanical Specifications (L77) Engine Mechanical Specifications (L77).
10. If the engine oil pressure is below specifications, inspect the engine for one or more of the following conditions:
* If equipped, valve lifter oil manifold filter plugged or damaged. Refer to Valve Lifter Oil Manifold Cleaning and Inspection 56. Valve Lifter Oil Manifold Cleaning and Inspection.
* If equipped, check if the engine oil cooler or oil cooler lines are plugged or damaged.
* Oil pump worn or dirty. Refer to Oil Pump Cleaning and Inspection (LS3, L76, L77) 51. Oil Pump Cleaning and Inspection (LS3, L76, L77).
* Oil pump-to-engine block bolts loose. Refer to Oil Pump, Screen and Crankshaft Oil Deflector Installation 72. Oil Pump, Screen and Crankshaft Oil Deflector Installation.
* Oil pump screen loose, plugged, or damaged. Refer to Oil Pump Cleaning and Inspection (LS3, L76, L77) 51. Oil Pump Cleaning and Inspection (LS3, L76, L77).
* Oil pump screen O-ring seal missing or damaged. Refer to Oil Pump Cleaning and Inspection (LS3, L76, L77) 51. Oil Pump Cleaning and Inspection (LS3, L76, L77).
* Excessive debris in the oil pan and/or oil filter (possibly indicating internal engine damage).
* Oil filter loose or a leaking or damaged gasket. Refer to Oil Filter, Adapter, and Pan Cover Installation 78. Oil Filter, Adapter, and Pan Cover Installation.
* Malfunctioning oil pump pressure relief valve. Refer to Oil Filter, Adapter, and Pan Cover Installation 78. Oil Filter, Adapter, and Pan Cover Installation.
* Excessive bearing clearance and/or bearing damage. Refer to Crankshaft and Bearing Cleaning and Inspection 34. Crankshaft and Bearing Cleaning and Inspection and Camshaft and Bearings Cleaning and Inspection 41. Camshaft and Bearings Cleaning and Inspection.
* Above acceptable bearing clearance. Refer to Engine Block Plug Removal 31. Engine Block Plug Removal.
* Cracked, porous, or restricted oil galleries. Refer to Engine Block Plug Installation 66. Engine Block Plug Installation.
* Oil gallery plugs missing or incorrectly installed. Refer to Engine Block Plug Installation 66. Engine Block Plug Installation.
* Broken valve lifters. Refer to Valve Lifter Replacement Valve Lifter Replacement.
Note: The following step applies to L76 engines equipped with active fuel management.
* If equipped, improper operation of the active fuel management oil pressure relief valve. Refer to Cylinder Deactivation (Active Fuel Management) Oil Pressure Relief Valve Diagnosis and Testing Cylinder Deactivation (Active Fuel Management) Oil Pressure Relief Valve Diagnosis and Testing.
Repair as necessary.
11. If the oil pressure reading on the J 21867 - pressure gauge (2), or equivalent, is within specifications, inspect for the following conditions:
* Plugged or incorrect oil filter and/or malfunctioning oil filter bypass valve. Refer to Engine Oil and Oil Filter Replacement Service and Repair.
* Malfunctioning engine oil pressure sensor or switch. Refer to Engine Oil Pressure Sensor and/or Switch Replacement Service and Repair.