Operation CHARM: Car repair manuals for everyone.

Anti-Lock Brake/Electronic Stabilization Program ITT Mark 60/ITT Mark 70 Component Overview






Anti-Lock Brake/Electronic Stabilization Program ITT Mark 60/ITT Mark 70 Component Overview






1 - ABS Control Module (J104)

• Beginning with MY 09, the ESP sensor unit (G419) is inside the ABS control module.

• Beginning with MY 09, the ABS control module must be replaced if the ESP sensor unit is faulty.

• Beginning with MY 09, the ABS control module must be calibrated if it was replaced.

• Beginning with MY 09, the steering angle and the braking pressure are stored in the ABS control module and must be calibrated.

• Component location: on the hydraulic unit in right of engine compartment

• Do not disconnect connector before successfully completing On Board Diagnostic (OBD). Switch ignition off before separating connector.

• ABS/ESP system ITT Mark 60, refer to => [ Control Module and Hydraulic Unit, ABS/ESP ITT Mark 60 ] Control Module and Hydraulic Unit, ABS/ESP ITT Mark 60

• Mark 60, removing and installing, refer to => [ Control Module and Hydraulic Unit, Mark 60, ] Control Module and Hydraulic Unit, Mark 60

• ABS system ITT Mark 70, refer to => [ Control Module and Hydraulic Unit, Anti-Lock Brake ITT Mark 70 Overview ] Control Module and Hydraulic Unit, Anti-Lock Brake ITT Mark 70 Overview

• Mark 70, removing and installing, refer to => [ Control Module and Hydraulic Unit, Mark 70 ] Control Module and Hydraulic Unit, Mark 70

• TFSI, removing and installing, refer to => [ ABS Control Module and ABS Hydraulic Unit ] ABS Control Module and ABS Hydraulic Unit

• 2.0L TDI removing and installing, refer to => [ ABS Control Module and ABS Hydraulic Unit ] ABS Control Module and ABS Hydraulic Unit

• Vehicles with a diesel particulate filter, removing and installing, refer to => [ ABS Control Module and ABS Hydraulic Unit with Diesel Particulate Filter ] ABS Control Module and ABS Hydraulic Unit With Diesel Particulate Filter

2 - ABS Hydraulic Unit (N55)

• Component location: on the hydraulic unit in right of engine compartment

• The ABS hydraulic pump (V64) , the ABS hydraulic unit (N55) and the ABS control module comprise the hydraulic control unit

• With an integrated brake pressure sensor 1 (G201)

• Mark 60, removing and installing, refer to => [ Control Module and Hydraulic Unit, Mark 60, ] Control Module and Hydraulic Unit, Mark 60

• ABS/ESP system ITT Mark 60, refer to => [ Control Module and Hydraulic Unit, ABS/ESP ITT Mark 60 ] Control Module and Hydraulic Unit, ABS/ESP ITT Mark 60

• ABS system ITT Mark 70, refer to => [ Control Module and Hydraulic Unit, Anti-Lock Brake ITT Mark 70 Overview ] Control Module and Hydraulic Unit, Anti-Lock Brake ITT Mark 70 Overview

• Mark 70, removing and installing, refer to => [ Control Module and Hydraulic Unit, Mark 70 ] Control Module and Hydraulic Unit, Mark 70

• TFSI, removing and installing, refer to => [ ABS Control Module and ABS Hydraulic Unit ] ABS Control Module and ABS Hydraulic Unit

• 2.0L TDI removing and installing, refer to => [ ABS Control Module and ABS Hydraulic Unit ] ABS Control Module and ABS Hydraulic Unit

• Vehicles with a diesel particulate filter, removing and installing, refer to => [ ABS Control Module and ABS Hydraulic Unit with Diesel Particulate Filter ] ABS Control Module and ABS Hydraulic Unit With Diesel Particulate Filter

• Allocation, refer to the electronic parts catalog ETKA

3 - ASR/ESP Button (E256)

• Component location: In the center console

4 - ESP Sensor Unit (G419)

• 20 Nm

• Through MY 08, the ESP sensor unit is located under the right seat.

• Beginning with MY 09, the sensor unit ESP sensor unit is inside the ABS control module.

• Beginning with MY 09, the ABS control module must be replaced if the ESP sensor unit is faulty.

• Beginning with MY 09, the ABS control module must be calibrated if it was replaced.

• Beginning with MY 09, the steering angle and the braking pressure are stored in the ABS control module and must be calibrated.

• Combined in one housing

• Combined sensor for transverse acceleration sensor (G200) and for rotation rate sensor (G202)

• On all-wheel drive vehicles, also longitudinal acceleration sensor (G251)

• ESP sensor unit, removing and installing, refer to => [ Electronic Stabilization Program Sensor Unit ] Service and Repair

5 - ASR/ESP Control Lamp (K155)

• Component location: In instrument cluster

6 - Brake Pad Wear Indicator Lamp (K32)

• Brake pad worn

• Component location: In instrument cluster

7 - Brake System Indicator Lamp (K118)

• Component location: In instrument cluster

• Brake malfunction, hand brake engaged

• Check brake fluid if blinking

8 - ABS Indicator Lamp (K47)

• Component location: In instrument cluster

9 - Parking Brake Indicator Lamp Switch (F9)

• Component location: On hand brake lever

10 - Right/Left Rear ABS Wheel Speed Sensor (G44) / (G46)

• Removing and installing, refer to => [ Speed Sensor at Rear Axle with Front-Wheel Drive ] Speed Sensor at Rear Axle With Front-Wheel Drive

11 - Wheel Bearing/Hub Unit

• The ABS sensor ring/rotor is installed in the wheel bearing

12 - Wheel Bearing Housing

13 - Steering Angle Sensor (G85)

• Component location: Coil ring with slip ring on steering column switch

• Removing and installing, refer to => [ Steering Angle Sensor (G85) ] Service and Repair

14 - Data Link Connector (DLC)

• Component location: cover in driver footwell

15 - Brake Lamp Switch (F)

• Brake lamp switch bolt: 5 Nm

• If the vehicle has a brake lamp switch depends on the model.

• Removing and installing, refer to => [ Brake Lamp Switch on Brake Pedal ] Brake Lamp Switch on Brake Pedal

• Brake Lamp Switch on Master Brake Cylinder, Removing and Installing, refer to => [ Brake Lamp Switch on Master Brake Cylinder ] Brake Lamp Switch on Master Brake Cylinder

16 - Right/Left Front ABS Wheel Speed Sensor (G45) / (G47)

• Removing and installing, refer to => [ Speed Sensor at Front Axle ] Speed Sensor at Front Axle

17 - Brake Master Cylinder

• Removing and installing, refer to => [ Brake Master Cylinder ] Brake Master Cylinder

• With attached brake lamp switch

• If the vehicle has a brake lamp switch depends on the model.

• Brake Lamp Switch on Master Brake Cylinder, Removing and Installing, refer to => [ Brake Lamp Switch on Master Brake Cylinder ] Brake Lamp Switch on Master Brake Cylinder

• Brake lamp switch bolt: 5 Nm

18 - Wheel Bearing/Hub Unit

• The ABS sensor ring/rotor is installed in the wheel bearing

19 - Wheel Bearing Housing

20 - Brake Fluid Level Warning Switch (F34)

=> Maintenance Procedures 03