Operation CHARM: Car repair manuals for everyone.

Subframe, Lower Transverse Link, Upper Transverse Link, Tie Rod and Level Control System Assembly Overview







Subframe, Lower Transverse Link, Upper Transverse Link, Tie Rod and Level Control System Assembly Overview






1 - Eccentric Bolt

• Perform a vehicle alignment after loosening. Refer to => [ Wheel Alignment ] Wheel Alignment.

• Do not turn more than 90° right or left (that is smallest to largest possible adjustment).

2 - Nut

• Self-locking

• 95 Nm

• Always replace if removed.

• Always tighten threaded connections in curb weight position.

3 - Eccentric Washer

• Inner bore with tab.

4 - Eccentric Bolt

• Perform a vehicle alignment after loosening. Refer to => [ Wheel Alignment ] Wheel Alignment.

• Do not turn more than 90° right or left (that is smallest to largest possible adjustment).

5 - Nut

• Self-locking

• 95 Nm

• Always replace if removed.

• Always tighten threaded connections in curb weight position.

• Adjust torque wrench VAG 1332 to 80 Nm when tightening nut.

• This torque specification applies only with insert tool T10179.

6 - Eccentric Washer

• Inner bore with tab.

7 - Subframe

• Different versions: Aluminum and steel.

• Only steel subframes are available as a replacement part. A new brake line must also be installed when replacing an aluminum subframe.

8 - Bolt

• 90 Nm + 90° turn

• Always replace if removed.

9 - Lower Transverse Link

• Removing and installing, refer to => [ Lower Transverse Link ] Lower Transverse Link.

10 - Nut

• Self-locking

• 90 Nm + 90° turn

• Always replace if removed.

• Always tighten threaded connections in curb weight position.

11 - Bolt

• Always replace if removed.

12 - Threaded Rivet

• M6

13 - Expanding Rivet

14 - Stone Protection Plate

15 - Bolt

• 8 Nm

16 - Bolt

• 5 Nm

• Installed on vehicles with electronic damping (Audi magnetic ride).

• Installed on vehicles with headlamp range control; quantity: 3

17 - Bolt

• 5 Nm

18 - Left Rear Level Control System Sensor (G76) , Right Rear Level Control System Sensor (G77)


• The sensor lever must face toward the outside of the vehicle.

19 - Bolt

• 130 Nm + 90° turn

• Always replace if removed.

• Always tighten threaded connections in curb weight position.

20 - Washer

• Installed on vehicles with an aluminum wheel bearing housing.

• Serves as corrosion protection.

• Always install.

21 - Upper Transverse Link

• Removing and installing, refer to => [ Upper Transverse Link ] Upper Transverse Link.

22 - Nut

• Always replace if removed.

23 - Washer

24 - Nut

• Always replace if removed.

25 - Wheel Bearing Housing

• Different versions: Aluminum and steel.

• Removing and installing, refer to => [ Wheel Bearing Housing ] Wheel Bearing Housing.

26 - Washer

• Installed on vehicles with an aluminum wheel bearing housing.

• Serves as corrosion protection.

• Always install.

27 - Washer

28 - Bolt

• 130 Nm + 90° turn

• Always replace if removed.

• Always tighten threaded connections in curb weight position.

29 - Tie Rod

• Closed in direction of travel.

30 - Nut

• 90 Nm + 90° turn

• Always replace if removed.

• Always tighten threaded connections in curb weight position.

31 - Bolt

• Always replace if removed.

32 - Nut

• 50 Nm + 180° turn

• Always replace if removed.

33 - Crossmember

• Omitted with the steel subframe.

34 - Bolt

• Always replace if removed.