Operation CHARM: Car repair manuals for everyone.

Lower Timing Chain Cover






Lower Timing Chain Cover

Special tools, testers and auxiliary items required

• Engine Support Bridge (10-222 A)

• Bracket with Spindle and Hook (10-222 A/10)

• Shackle (10-222 A/12)

• Adapter (10-222 A/13) (Qty: 2)

• Locking Pin (T10060 A)

• Bits (T10099)

• Counter Hold Tool (T10355)

• Thrust Piece (T10368)

• Torque Wrench (5-50 Nm) (V.A.G 1331)

• Torque Wrench (40-200 Nm) (V.A.G 1332)

• Silicone Sealant (D 174 003 A3)

• Flat Scraper

• Hand Drill with Plastic Brush Attachment

• Protective Eyewear

• Feeler Gauge

Removing

- Remove the noise insulation.

- Remove the right front wheel.

- Remove the right front wheel housing liner.

- Drain the engine oil.






- Remove the bolts - arrows -.

- Remove the charge air pipe by lifting the clamps - 1 and 2 -.

- Remove the ribbed belt. Refer to => [ Ribbed Belt ] Ribbed Belt.

- Use the counter hold tool (T10355) to rotate the vibration damper to Top Dead Center (TDC) - arrow -:






• The notch on the vibration damper must line up with the arrow mark on the lower timing chain cover.


The engine could be destroyed:

• In order NOT to change the valve timing, the crankshaft must NOT be moved out of the TDC position when the vibration damper bolt is removed.

- Use the counter hold tool (T10355) tool to remove the vibration damper bolt.

- Remove the vibration damper.


To avoid damaging the splines, only use the thrust piece (T10368) to install the vibration damper bolt.

- Install the vibration damper bolt and the thrust piece (T10368).






- Remove the charge air pipe from the noise generator, if equipped. Refer to => [ Charge Air Pipe from Noise Generator ] Charge Air Pipe from Noise Generator.

- Install the engine support bridge (10-222 A) using the following tools:






• Bracket with spindle and hook (10-222 A/10)

• Shackle (10-222 A/12)

• Adapter (10-222 A/13) (Qty: 2)

- Tension the engine with the spindle.

- Remove the engine mount to engine mount bracket bolts - arrows -.






- Remove the engine mount. Refer to => [ Engine and Transmission Mount Overview ] Engine and Transmission Mount Overview.

- Lift the engine approximately 50 mm and loosen the upper bolt for the engine mount bracket.

- Now, lower the engine approximately 100 mm.

- Free up the electrical harness - arrow -.






- Remove the bolt - 1 - and remove the ribbed belt tensioner from the accessory bracket.

- Remove the lower engine mount bracket bolts using the bits (T10099).

- Remove the engine mount bracket and bolts.

- Remove the bolts - 1 - and pull the oil dipstick guide tube out.






- Remove the wastegate bypass regulator valve (N75) bolts - arrows - and the valve from the turbocharger.






- Remove the turbocharger support bolts - 1 -.

- Remove the bolts - 1 through 15 -.







The lower timing chain cover could be damaged. To avoid deformation, do not hold between the bolting points.

- Pry off the lower timing chain cover; when doing this, begin at - 1 and 2 -.






Installing

• Lower timing chain cover bolt tightening sequence and specification. Refer to => [ Lower Timing Chain Cover Bolt Tightening
Sequence and Specification ] Timing Chain Covers Overview.

• Timing chain cover tightening specifications. Refer to => [ Timing Chain Covers Overview ] Timing Chain Covers Overview.

• Turbocharger tightening specifications. Refer to => [ Turbocharger Component Overviews ] Turbocharger Component Overviews.

• Ribbed belt tightening specification. Refer to => [ Ribbed Belt Overview ] Ribbed Belt Overview.

• Engine/transmission tightening specifications. Refer to => [ Engine and Transmission Mount Overview ] Engine and Transmission Mount Overview.

• Use silicone sealant (D 174 003 A3).

• The sealing surfaces must be completely free of oil and grease.

• Note the expiration date of the silicone sealant.

• The cover must be installed within 5 minutes after applying the silicone sealant.

• Replace the bolts which are being tightened to a torque angle.

• Replace sealing rings, seals and self-locking nuts.

- Remove any sealant residue on the cylinder block using a flat blade scraper.


Risk of eye injury.

• Wear protective eyewear.

- Seal off both sides of the seal with tape to prevent contamination.

- Remove any residual sealant from the cover with a rotating plastic brush.






- Clean the sealing surfaces, they must be free of oil and grease.

- Install the cover with the old bolts and tighten:

• Tightening specification: 8 Nm.

- Check the gap between the cover and the housing using a feel gauge.

• It may not exceed 0.2 mm.

• If the gap exceeds 0.2 mm, replace the cover.

• It is not possible to measure between the cover the upper oil pan, however check the sealing surface for evenness.

- Make sure both alignment bushings for centering the cover - arrows - are present.






- Cut the sealant tube nozzle at the front mark (nozzle diameter: approximately 0.12 in).






- Apply the silicone sealant to the clean sealing surface of the cover as shown.






• Thickness of the sealant bead: 2 to 3 mm.

• The cover must be installed within 5 minutes after applying the silicone sealant.

• The sealant bead may not be thicker than specified, otherwise the excess sealant could enter the oil pan and clog the oil intake tube.

• Note the expiration date of the silicone sealant.

- Install the cover immediately and tighten the new bolts:

- Tighten the bolts - 1 through 15 - in 2 passes in the sequence shown:






1 - Tighten the bolts to 8 Nm

2 - Tighten the bolts an additional 45° (1/8) turn.

• After installing the cover, allow the sealant to dry for approximately 30 minutes. Only after then may the engine oil be added.

- Fill the engine oil.

- Check the oil level. Refer to => [ Oil Level, Checking ] Testing and Inspection.

Further installation is in the reverse order of removal.