Operation CHARM: Car repair manuals for everyone.

Removal








2AZ-FE ENGINE MECHANICAL: TIMING CHAIN:

REMOVAL

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (Removal)

3. REMOVE FRONT WHEEL RH
4. REMOVE ENGINE UNDER COVER LH
5. REMOVE ENGINE UNDER COVER RH
6. REMOVE FRONT FENDER APRON SEAL RH
7. DRAIN ENGINE OIL (Replacement)

8. REMOVE FRONT EXHAUST PIPE ASSEMBLY
HINT: (Removal).

9. REMOVE NO. 2 ENGINE MOUNTING STAY RH (Removal)

10. REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY (Removal)

11. REMOVE NO. 2 ENGINE MOUNTING BRACKET RH (Removal)

12. REMOVE V-RIBBED BELT (Removal)

13. REMOVE GENERATOR ASSEMBLY (Removal)

14. REMOVE VANE PUMP ASSEMBLY (Removal)

15. REMOVE IGNITION COIL ASSEMBLY (Removal)

16. DISCONNECT VENTILATION HOSE
17. DISCONNECT NO. 2 VENTILATION HOSE
18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY





(a) Remove the 2 bolts and disconnect the 2 engine wires.





(b) Remove the 8 bolts, 2 nuts, and the cylinder head cover.
19. SET NO. 1 CYLINDER TO TDC/COMPRESSION (Adjustments)

20. REMOVE CRANKSHAFT PULLEY (Removal)

21. REMOVE CRANK POSITION SENSOR (Removal)

22. REMOVE OIL PAN SUB-ASSEMBLY





(a) Remove the 12 bolts and 2 nuts.





(b) Insert the blade of an oil pan seal cutter between the crankcase and oil pan. Cut through the sealer and remove the oil pan.

NOTE: Be careful not to damage the contact surfaces of the crankcase, chain cover and oil pan.

23. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY





(a) Remove the 2 nuts, tensioner and gasket.

NOTE: Do not turn the crankshaft without the chain tensioner.

24. INSTALL ENGINE HANGERS





(a) Install the No. 1 engine hanger and No. 2 engine hanger with the bolts as shown in the illustration.
Parts No.:





Torque: 38 Nm (387 kgf-cm, 28 ft-lbf)
(b) Attach the sling device to the engine hangers and chain block.
25. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
(a) Lift the engine upward using the chain block.

NOTE: Do not lift the engine more than necessary.

(b) Spring type:





(1) Remove the bolt, nut and tensioner.
(c) Except spring type:





(1) Remove the bolt, nut and tensioner.
26. REMOVE ENGINE MOUNTING INSULATOR





(a) Attach the engine chain hoist to the engine hangers.

CAUTION: Do not attempt to hang the engine by hooking the chain to any other part.

(b) Remove the bolt and disconnect the engine mounting insulator FR.





(c) M/T:
Remove the bolt and disconnect the engine lateral control rod.





(d) Remove the 2 bolts and disconnect the steering gear return tube clamps from the frame.





(e) Remove the 4 nuts from the engine mounting insulator RH.
(f) Raise the engine and remove the engine mounting insulator RH.
27. REMOVE ENGINE MOUNTING BRACKET RH





(a) Remove the 3 bolts and engine mounting bracket.
28. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY (Removal)

29. REMOVE TIMING CHAIN CASE OIL SEAL (Removal)

30. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE





(a) Remove the crankshaft position sensor plate.
31. REMOVE CHAIN TENSIONER SLIPPER





(a) Remove the bolt and chain tensioner slipper.
32. REMOVE NO. 1 CHAIN VIBRATION DAMPER





(a) Remove the 2 bolts and chain vibration damper.
33. REMOVE TIMING CHAIN GUIDE





(a) Remove the bolt and timing chain guide.
34. REMOVE CHAIN SUB-ASSEMBLY





(a) Remove the chain sub-assembly.
35. REMOVE CRANKSHAFT TIMING SPROCKET





(a) Remove the crankshaft timing sprocket.
36. REMOVE NO. 2 CHAIN SUB-ASSEMBLY





(a) Turn the crankshaft by 90° counterclockwise to align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.





(b) Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft sprocket to lock the gear in position, and then remove the nut.





(c) Remove the bolt, chain tensioner plate and spring.





(d) Remove the chain tensioner, oil pump driven sprocket and chain.