Operation CHARM: Car repair manuals for everyone.

Short in CAN Bus Lines





CAN COMMUNICATION: CAN COMMUNICATION SYSTEM: Short in CAN Bus Lines
- Short in CAN Bus Lines

DESCRIPTION

There may be a short circuit between the CAN bus line and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 54 Ohms.





WIRING DIAGRAM





INSPECTION PROCEDURE

NOTICE:
* Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
* After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
* Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
HINT
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

PROCEDURE

1. CHECK CAN BUS LINES FOR SHORT CIRCUIT (DLC3 BRANCH WIRE)

(a) Turn the ignition switch OFF.





(b) Disconnect the D41 D-CAN J/C connector.

(c) Measure the resistance.





Standard resistance:





NG -- REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK -- Continue to next step.

2. CONNECT CONNECTOR

(a) Reconnect the D41 D-CAN J/C connector.

NEXT -- Continue to next step.

3. CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C SIDE)

(a) Turn the ignition switch OFF.





(b) Disconnect the D42 P-CAN J/C connector.

(c) Measure the resistance.





Standard resistance:





OK -- CONNECT CONNECTOR
NG -- Continue to next step.

4. CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - P-CAN J/C)

(a) Turn the ignition switch OFF.





(b) Disconnect the D41 D-CAN J/C connector.

(c) Measure the resistance.

HINT
The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

Standard resistance:





NG -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C (CAN-H, CAN-L))
OK -- Continue to next step.

5. CONNECT CONNECTOR

(a) Reconnect the D41 D-CAN J/C connector.

(b) Reconnect the D42 P-CAN J/C connector.

NEXT -- Continue to next step.

6. CHECK CAN BUS LINES FOR SHORT CIRCUIT (ECM)

(a) Turn the ignition switch OFF.





(b) Disconnect the A21 ECM connector.

(c) Measure the resistance.





Standard resistance:





OK -- REPLACE ECM
NG -- Continue to next step.

7. CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - ECM)

(a) Turn the ignition switch OFF.





(b) Disconnect the D41 D-CAN J/C connector.

(c) Measure the resistance.





HINT
The resistance must be measured after the A21 ECM connector is disconnected.

Standard resistance:





NG -- REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (D-CAN J/C - ECM (CAN-H, CAN-L))
OK -- Continue to next step.

8. CONNECT CONNECTOR

(a) Reconnect the D41 D-CAN J/C connector.

(b) Reconnect the A21 ECM connector.

NEXT -- Continue to next step.

9. CHECK CAN BUS LINES FOR SHORT CIRCUIT (AIR CONDITIONING AMPLIFIER)

NOTICE:
For vehicles without air conditioning or PTC heater, go to step 12

(a) Turn the ignition switch OFF.





(b) Disconnect the E8 air conditioning amplifier connector.

(c) Measure the resistance.





Standard resistance:





OK -- REPLACE AIR CONDITIONING AMPLIFIER
NG -- Continue to next step.

10. CHECK CAN BUS LINES FOR SHORT CIRCUIT (AIR CONDITIONING AMPLIFIER BRANCH WIRE)

(a) Turn the ignition switch OFF.





(b) Disconnect the D41 D-CAN J/C connector.

(c) Measure the resistance.





HINT
The resistance must be measured after the E8 air conditioning amplifier connector is disconnected.

Standard resistance:





NG -- REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CAN-H, CAN-L)
OK -- Continue to next step.

11. CONNECT CONNECTOR

(a) Reconnect the D41 D-CAN J/C connector.

(b) Reconnect the E8 air conditioning amplifier connector.

NEXT -- Continue to next step.

12. CHECK CAN BUS LINES FOR SHORT CIRCUIT (BRAKE ACTUATOR (SKID CONTROL ECU))

NOTICE:
For vehicles without ABS, go to step 15.

(a) Turn the ignition switch OFF.





(b) Disconnect the A15 brake actuator (skid control ECU) connector.

(c) Measure the resistance.





Standard resistance:





OK -- REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
NG -- Continue to next step.

13. CHECK CAN BUS LINES FOR SHORT CIRCUIT (BRAKE ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)

(a) Turn the ignition switch OFF.





(b) Disconnect the D41 D-CAN J/C connector.

(c) Measure the resistance.





HINT
The resistance must be measured after the A15 brake actuator (skid control ECU) connector is disconnected.

Standard resistance:





NG -- REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR (CAN-H, CAN-L)
OK -- Continue to next step.

14. CONNECT CONNECTOR

(a) Reconnect the D41 D-CAN J/C connector.

(b) Reconnect the A15 brake actuator (skid control ECU) connector.

NEXT -- Continue to next step.

15. CHECK CAN BUS LINES FOR SHORT CIRCUIT (CENTER AIRBAG SENSOR ASSEMBLY)

(a) Turn the ignition switch OFF.





(b) Disconnect the D16 center airbag sensor assembly connector.

(c) Measure the resistance.





Standard resistance:





OK -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
NG -- Continue to next step.

16. CHECK CAN BUS LINES FOR SHORT CIRCUIT (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)

(a) Turn the ignition switch OFF.





(b) Disconnect the D41 D-CAN J/C connector.

(c) Measure the resistance.





HINT
The resistance must be measured after the D16 center airbag sensor assembly connector is disconnected.

Standard resistance:





NG -- REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CAN-H, CAN-L)

OK -- REPAIR OR REPLACE D-CAN J/C (JUNCTION CONNECTOR)

17. CONNECT CONNECTOR

(a) Reconnect the D42 P-CAN J/C connector.

NEXT -- Continue to next step.

18. CHECK CAN BUS LINES FOR SHORT CIRCUIT (POWER STEERING ECU)

(a) Turn the ignition switch OFF.





(b) Disconnect the D31 power steering ECU connector.

(c) Measure the resistance.





Standard resistance:





OK -- REPLACE POWER STEERING ECU
NG -- Continue to next step.

19. CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C - POWER STEERING ECU)

(a) Turn the ignition switch OFF.





(b) Disconnect the D42 P-CAN J/C connector.

(c) Measure the resistance.





HINT
The resistance must be measured after the D31 power steering ECU connector is disconnected.

Standard resistance:





NG -- REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER STEERING ECU (P-CAN J/C - POWER STEERING ECU)
OK -- Continue to next step.

20. CONNECT CONNECTOR

(a) Reconnect the D42 P-CAN J/C connector.

(b) Reconnect the D31 power steering ECU connector.

NEXT -- Continue to next step.

21. CHECK CAN BUS LINES FOR SHORT CIRCUIT (MAIN BODY ECU)

(a) Turn the ignition switch OFF.





(b) Disconnect the D33 main body ECU connector.

(c) Measure the resistance.





Standard resistance:





OK -- REPLACE MAIN BODY ECU
NG -- Continue to next step.

22. CHECK CAN BUS LINES FOR SHORT CIRCUIT (MAIN BODY ECU BRANCH WIRE)

(a) Turn the ignition switch OFF.





(b) Disconnect the D42 P-CAN J/C connector.

(c) Measure the resistance.





HINT
The resistance must be measured after the D33 main body ECU connector is disconnected.

Standard resistance:





NG -- REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CAN-H, CAN-L)
OK -- Continue to next step.

23. CONNECT CONNECTOR

(a) Reconnect the D42 P-CAN J/C connector.

(b) Reconnect the D33 main body ECU connector.

NEXT -- Continue to next step.

24. CHECK CAN BUS LINES FOR SHORT CIRCUIT (COMBINATION METER ECU)

(a) Turn the ignition switch OFF.





(b) Disconnect the D1 combination meter ECU connector.

(c) Measure the resistance.





Standard resistance:





OK -- REPLACE COMBINATION METER ECU
NG -- Continue to next step.

25. CHECK CAN BUS LINES FOR SHORT CIRCUIT (COMBINATION METER ECU BRANCH WIRE)

(a) Turn the ignition switch OFF.





(b) Disconnect the D42 P-CAN J/C connector.

(c) Measure the resistance.





HINT
The resistance must be measured after the D1 combination meter ECU connector is disconnected.

Standard resistance:





NG -- REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO COMBINATION METER ECU (CAN-H, CAN-L)

OK -- REPAIR OR REPLACE P-CAN J/C (JUNCTION CONNECTOR)