Open in CAN Main Wire
NETWORKING: CAN COMMUNICATION SYSTEM: Open in CAN Main Wire
- Open in CAN Main Wire
DESCRIPTION
There may be an open circuit in the CAN main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ohms or higher.
* *: w/ Air Suspension System
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Service Precautions.
NEXT -- Continue to next step.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
(a) Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.
NEXT -- Continue to next step.
3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - DLC3)
(a) Disconnect the H119 No. 1 junction connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK -- Continue to next step.
4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - ECM)
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- CONNECT CONNECTOR
OK -- Continue to next step.
5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
Result
B -- CONNECT CONNECTOR
C -- CONNECT CONNECTOR
A -- REPLACE NO. 1 JUNCTION CONNECTOR
6. CONNECT CONNECTOR
(a) Reconnect the H119 No. 1 junction connector.
NEXT -- Continue to next step.
7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)
(a) Disconnect the H115 No. 2 junction connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- CONNECT CONNECTOR
OK -- Continue to next step.
8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK -- REPLACE NO. 2 JUNCTION CONNECTOR
9. CONNECT CONNECTOR
(a) Reconnect the H115 No. 2 junction connector.
NEXT -- Continue to next step.
10. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 2 JUNCTION CONNECTOR)
(a) Disconnect the A27 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
Result
B -- REPLACE ECM Removal
C -- REPLACE ECM Removal
D -- REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 2 JUNCTION CONNECTOR)
A -- REPLACE ECM Removal
11. CONNECT CONNECTOR
(a) Reconnect the H119 No. 1 junction connector.
NEXT -- Continue to next step.
12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)
(a) Disconnect the H37 combination meter assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)
OK -- REPLACE COMBINATION METER ASSEMBLY Removal
13. CONNECT CONNECTOR
(a) Reconnect the H119 No. 1 junction connector.
NEXT -- Continue to next step.
14. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
(a) Disconnect the O41 No. 4 junction connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- CONNECT CONNECTOR
OK -- Continue to next step.
15. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK -- REPLACE NO. 4 JUNCTION CONNECTOR
16. CONNECT CONNECTOR
(a) Reconnect the O41 No. 4 junction connector.
NEXT -- Continue to next step.
17. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 4 JUNCTION CONNECTOR)
(a) Disconnect the H37 combination meter assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 4 JUNCTION CONNECTOR)
OK -- REPLACE COMBINATION METER ASSEMBLY Removal