Operation CHARM: Car repair manuals for everyone.

Inspection Procedure N-9

ETACS-ECU does not receive any signal from the trunk lid latch switch or trunk light switch .

Trunk Lid Latch Switch Or Trunk Light Switch Input Circuit Part 1:




Trunk Lid Latch Switch Or Trunk Light Switch Input Circuit Part 2:






CIRCUIT OPERATION
The ETACS-ECU uses the input signal from the trunk lid latch switch or trunk light switch to operate the following functions.

TECHNICAL DESCRIPTION (COMMENT)
The trunk lid latch switch or trunk light switch input signal is used to operate the theft-alarm system and trunk light. If the signal fails, these function will not work normally.

TROUBLESHOOTING HINTS
- The trunk lid latch switch or trunk light switch may be defective
- The ETACS-ECU may be defective
- The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector

DIAGNOSIS

Required Special Tools:
- MB991223: Harness Set
- MB991502: Scan Tool (MUT-II)







STEP 1. Check the trunk lid latch switch or trunk light switch .

Q: Is the trunk lid latch switch or trunk light switch in good condition?

YES: Go to Step 2.

NO: Replace the trunk lid latch switch or trunk light switch . The input signal from the trunk lid latch switch or trunk light switch should be able to be checked and the functions, which are described in the "Technical Description (comment)," should work normally.







STEP 2. Check the ground circuit to the trunk lid latch switch or trunk light switch . Test at trunk lid latch switch connector F-21 or trunk light switch connector F-20 .

1. Disconnect trunk lid latch switch connector F-21 or trunk light switch connector F-20 and measure the resistance available at the harness side of the connector.

2. Measure the resistance between terminal 2 and ground.
- The resistance should equal 2 ohms or less.

Q: Is the measured resistance 2 ohms or less?

YES: Go to Step 5.

NO: Go to Step 3.




STEP 3. Check trunk lid latch switch connector F-21 or trunk light switch connector F-20 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q: Is trunk lid latch switch connector F-21 or trunk light switch connector F-20 in good condition?

YES: Go to Step 4.

NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. The input signal from the trunk lid latch switch or trunk light switch should be able to be checked and the functions, which are described in the "Technical Description (comment)," should work normally.




STEP 4. Check the harness wire between trunk lid latch switch connector F-21 (terminal 2) or trunk light switch connector F-20 (terminal 2) and the ground.

Q: Is the harness wire between trunk lid latch switch connector F-21 (terminal 2) or trunk light switch connector F-20 (terminal 2) and the ground in good condition?

YES: No action is necessary and testing is complete.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. The input signal from the trunk lid latch switch or trunk light switch should be able to be checked and the functions, which are described in the "Technical Description (comment)," should work normally.







STEP 5. Check trunk lid latch switch connector F-21 or trunk light switch connector F-20 and ETACS-ECU connector C-95 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q:
Are trunk lid latch switch connector F-21 or trunk light switch connector F-20 and ETACS-ECU connector C-95 in good condition?

YES: Go to Step 6.

NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. The input signal from the trunk lid latch switch or trunk light switch should be able to be checked and the functions, which are described in the "Technical Description (comment)," should work normally.










STEP 6. Check the harness wires between trunk lid latch switch connector F-21 (terminal 1) or trunk light switch connector F-20 (terminal 1) and ETACS-ECU connector C-95 (terminal 37).

NOTE:
Also check intermediate connector C-67 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-67 is damaged, repair or replace it. Refer to Harness Connector Inspection.

Q: Are the harness wires between trunk lid latch switch connector F-21 (terminal 1) or trunk light switch connector F-20 (terminal 1) and ETACS-ECU connector C-95 (terminal 37) in good condition?

YES: Replace the ETACS-ECU. The input signal from the trunk lid latch switch or trunk light switch should be able to be checked and the functions, which are described in the "Technical Description (comment)," should work normally.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. The input signal from the trunk lid latch switch or trunk light switch should be able to be checked and the functions, which are described in the "Technical Description (comment)," should work normally.