Operation CHARM: Car repair manuals for everyone.

Inspection Procedure K-4

Interior Light: The ignition key hole illumination light does not illuminate or go out normally.

NOTE: This troubleshooting procedure requires the use of scan tool MB991502 and SWS monitor kit MB991862. For details on how to use the SWS monitor, refer to "How to use SWS monitor."

Ignition Key Hole Illumination Light Circuit Part 1:




Ignition Key Hole Illumination Light Circuit Part 2:






CIRCUIT OPERATION
- When the driver's door is opened with the ignition switch at "ACC" position, the ETACS-ECU illuminates the ignition key hole illumination light.
- The ignition key hole illumination light goes out in 30 seconds after the driver's door is closed. The ignition key hole illumination light remains illuminated for 30 seconds after the ignition key is pulled out.

- The ETACS-ECU operates the ignition key hole illumination light according to the input signals from the following switches:
- Ignition switch (IG1): OFF
- Key reminder switch: OFF
- Interior light loaded signal: ON

- Vehicle condition:
- Ignition switch: "LOCK" (OFF) or "ACC" position
- Ignition key: Removed from the ignition key cylinder
- Driver's door: Opened, or close

TECHNICAL DESCRIPTION (COMMENT)
Is the ignition key hole illumination light does not illuminate, the input circuits from the switches described in "CIRCUIT OPERATION", the key reminder switch (ignition key hole illumination light bulb) or the ETACS-ECU may be defective.

TROUBLESHOOTING HINTS
- The driver's door switch may be defective
- The key reminder switch (key reminder switch or ignition key hole illumination light bulb) may be defective
- The ETACS-ECU may be defective
- The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector

DIAGNOSIS

Required Special Tools:
- MB991223: Harness Set
- MB991502: Scan Tool (MUT-II)
- MB991862: SWS monitor kit







STEP 1. Use scan tool MB991502 to select "ECU COMM CHK" on the SWS monitor display.

Check the ETACS-ECU.

CAUTION:
To prevent damage to scan tool MB991502, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991502. Connect the DLC harness before connecting the column-ECU harness. Be sure to connect SWS monitor kit MB991862 after turning on scan tool MB991502.

1. Connect scan tool MB991502 to the data link connector.
2. Connect SWS monitor kit MB991862 to the column switch connector.
3. Turn the ignition switch to the "LOCK" (OFF) position.

4. Operate scan tool MB991502 according to the procedure below to display "ECU COMM CHK."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "ECU COMM CHK."

5. Scan tool MB991502 should show "OK" on the "ECU COMM CHK" menu for the "ETACS ECU" menu.

Q: Is "OK" displayed on the "ETACS ECU" menu?

YES: Go to Step 2.

NO: Refer to Inspection Procedure A-3 "Communication with ETACS-ECU is not possible."







STEP 2. Check the input signal by using "DATA LIST" menu of the SWS monitor.

Check the input signals from the following switches:
- Ignition switch: OFF
- Driver's door: open
- Front passenger's door: closed

Operate scan tool MB991502 according to the procedure below to display "ETACS ECU."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "DATA LIST."
5. Select "ETACS ECU."




Check that normal conditions are displayed on the items described in the table.

Q: Does the scan tool display the items "IG SW (IG1)" and "FRONT DOOR SW" as normal condition?

YES: Go to Step 3.

NO:
- Normal condition is not displayed for "IG SW (IG1)": Refer to Inspection Procedure M-2 "ETACS-ECU does not receive any signal from the ignition switch (IG1)."
- Normal condition is not displayed for "FRONT DOOR SW": Refer to Inspection Procedure M-4 "ETACS-ECU does not receive any signal from the driver's or the front passenger's door switch."




STEP 3. Check the input signal by using the pulse check mode of the monitor.

Check the following switches and input signals:
- Key reminder switch
- Interior light loaded signal

Operate scan tool MB991502 according to the procedure below to display "PULSE CHECK."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "PULSE CHECK."




If the switches (see table), which are applicable for the input signal check, are operated, check if scan tool MB991502 sounds or not.

Q: When the key reminder switch and the interior light are operated, does scan tool MB991502 sound in each case?

YES: Go to Step 4.

NO:
- Scan tool MB991502 does not sound when the ignition key is removed and reinserted: Refer to Inspection Procedure N-1 "ETACS-ECU does not receive a signal from the key reminder switch."
- When one of the interior lights is illuminated, scan tool MB991502 does not sound: Refer to Inspection Procedure N-12 "ETACS-ECU does not receive any interior light loaded signal."

STEP 4. Check the ignition key hole illumination light bulb.

Q: Is the ignition key hole illumination light bulb in good condition?

YES: Go to Step 5.

NO: Replace the bulb. Verify that the ignition key hole illumination light illuminates normally.




STEP 5. Check the key reminder switch (ignition key hole illumination).

1. Disconnect key reminder switch connector C-59.
2. Remove the ignition key hole illumination light bulb. Then measure the resistance value between the bulb terminals.
3. Install a bulb to the key remainder switch, and measure the resistance between connector C-59 terminals 1 and 2. The measured resistance value should be roughly the same as the value measured in Step (2).

Q: Are these two resistance values extremely different?

YES: Replace the key reminder switch. Verify that the ignition key hole illumination light illuminates normally.

NO (much the same): Go to Step 6.







STEP 6. Measure at key reminder switch connector C-59 in order to check the fusible link (1) line of the power supply to the key reminder switch (ignition key hole illumination light).

1. Disconnect key reminder switch connector C-59 and measure the voltage available at the wiring harness side of the connector.

2. Measure the voltage between terminal 2 and ground.
- The voltage should measure approximately 12 volts (battery positive voltage).

Q: Is the measured voltage approximately 12 volts (battery positive voltage)?

YES: Go to Step 9.

NO: Go to Step 7.







STEP 7. Check key reminder switch connector C-59 and ETACS-ECU connector C-94 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q: Are key reminder switch connector C-59 and ETACS-ECU connector C-94 in good condition?

YES: Go to Step 8.

NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that the ignition key hole illumination light illuminates normally.










STEP 8. Check the wiring harness between key reminder switch connector C-59 (terminal 2) and ETACS-ECU connector C-94 (terminal 71).

NOTE: Also check joint connector C-57 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If joint connector C-57 is damaged, repair or replace the connector as described in Harness Connector Inspection.

Q: Is the wiring harness between key reminder switch connector C-59 (terminal 2) and ETACS-ECU connector C-94 (terminal 71) in good condition?

YES: No action is necessary and testing is complete.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the ignition key hole illumination light illuminates normally.







STEP 9. Check key reminder switch connector C-59 and ETACS-ECU connector C-94 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q: Are key reminder switch connector C-59 and ETACS-ECU connector C-94 in good condition?

YES: Go to Step 10.

NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that the ignition key hole illumination light illuminates normally.







STEP 10. Check the wiring harness between key reminder switch connector C-59 (terminal 1) and ETACS-ECU connector C-94 (terminal 69).

Q: Is the wiring harness between key reminder switch connector C-59 (terminal 1) and ETACS-ECU connector C-94 (terminal 69) in good condition?

YES: Replace the ETACS-ECU. Verify that the ignition key hole illumination light illuminates normally.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the ignition key hole illumination light illuminates normally.