Inspection Procedure K-2
Interior Light: The front dome light, rear dome light or trunk light does not illuminate or go out normally.Interior Lights And Trunk Light Circuit Part 1:
Interior Lights And Trunk Light Circuit Part 2:
CIRCUIT OPERATION
The ETACS-ECU operates the dome light according to the following signals:
- Ignition switch (IG1): ON or OFF
- Key reminder switch: ON or OFF
- Front door switch: ON or OFF
- All door switches: ON or OFF
- Driver's door lock actuator switch: LOCK or UNLOCK
TECHNICAL DESCRIPTION (COMMENT)
Is the dome light does not flash normally, a burned-out dome light bulb, the input circuits from the switches described in "CIRCUIT OPERATION", the power supply line to the switches or the ETACS-ECU may be defective.
TROUBLESHOOTING HINTS
- The key reminder switch may be defective
- The door switch may be defective
- The driver's door lock actuator switch may be defective
- The dome light may be defective
- The ETACS-ECU may be defective
- The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector
DIAGNOSIS
Required Special Tools:
- MB991223: Harness Set
- MB991502: Scan Tool (MUT-II)
STEP 1. Check which of the front dome light, the rear dome light or the trunk light does not illuminate normally.
Q: Which of the front dome light, the rear dome light or the trunk light fail to illuminate normally?
Front dome light: Go to Step 2.
Rear dome Light: Go to Step 11.
Trunk light: Go to Step 17.
STEP 2. Check the front dome light bulb.
Q: Is the front dome light bulb in good condition?
YES: Go to Step 3.
NO: Replace the front dome light bulb. Verify that the front dome light illuminates normally.
STEP 3. Check the ETACS-ECU line of the power supply circuit to the front dome light. Test at front dome light connector D-06.
1. Disconnect front dome light connector D-06 and measure the voltage available at the wiring harness side of the connector.
2. Measure the voltage between terminal 3 and ground.
- The voltage should measure approximately 12 volts (battery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery positive voltage)?
YES: Go to Step 6.
NO: Go to Step 4.
STEP 4. Check front dome light connector D-06 and ETACS-ECU connector C-95 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q: Are front dome light connector D-06 and ETACS-ECU connector C-95 in good condition?
YES: Go to Step 5.
NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that the front dome light illuminates normally.
STEP 5. Check the wiring harness between front dome light connector D-06 (terminal 3) and ETACS-ECU connector C-95 (terminal 6).
NOTE: Also check intermediate connector C-27 and junction block connector C-78 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-27 or junction block connector C-78 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.
Q: Is the wiring harness between front dome light connector D-06 (terminal 3) and ETACS-ECU connector C-95 (terminal 6) in good condition?
YES: No action is necessary and testing is complete.
NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the front dome light illuminates normally.
STEP 6. Check the ground circuit to the front dome light. Test at front dome light connector D-06.
1. Disconnect front dome light connector D-06 and measure the resistance available at the wiring harness side of the connector.
2. Measure the resistance value between terminal 1 and ground.
- The resistance should measure 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES: Go to Step 9.
NO: Go to Step 7.
STEP 7. Check front dome light connector D-06 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q: Is front dome light connector D-06 in good condition?
YES: Go to Step 8.
NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Check that the fog lights illuminate normally.
STEP 8. Check the wiring harness between front dome light connector D-06 (terminal 1) and ground.
Q: Is the wiring harness between front dome light connector D-06 (terminal 1) and ground in good condition?
YES: No action is necessary and testing is complete.
NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the front dome light illuminates normally.
STEP 9. Check front dome light connector D-06 and ETACS-ECU connector C-95 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q: Are front dome light connector D-06 and ETACS-ECU connector C-95 in good condition?
YES: Go to Step 10.
NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that the front dome light illuminates normally.
STEP 10. Check the wiring harness between front dome light connector D-06 (terminal 2) and ETACS-ECU connector C-95 (terminal 5).
NOTE: Also check intermediate connector C-27 and junction block connector C-78 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-27 or junction block connector C-78 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.
Q: Is the wiring harness between front dome light connector D-06 (terminal 2) and ETACS-ECU connector C-95 (terminal 5) in good condition?
YES: Replace the ETACS-ECU. Verify that the front dome light illuminates normally.
NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the front dome light illuminates normally.
STEP 11. Check the rear dome light bulb.
Q: Is the rear dome light bulb in good condition?
YES: Go to Step 12.
NO: Replace the rear dome light bulb. Verify that the rear dome lights illuminate normally.
STEP 12. Check the ETACS-ECU line of the power supply circuit to the rear dome light. Test at rear dome light connector D-27.
1. Disconnect rear dome light connector D-27 and measure the voltage available at the wiring harness side of the connector.
2. Measure the voltage between terminal 1 and ground.
- The voltage should measure approximately 12 volts (battery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery positive voltage)?
YES: Go to Step 15.
NO: Go to Step 13.
STEP 13. Check rear dome light connector D-27 and ETACS-ECU connector C-95 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q: Are rear dome light connector D-27 and ETACS-ECU connector C-95 in good condition?
YES: Go to Step 14.
NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that the rear dome lights illuminate normally.
STEP 14. Check the wiring harness between rear dome light connector D-27 (terminal 1) and ETACS-ECU connector C-95 (terminal 6).
NOTE: Also check intermediate connectors C-27, D-26 and junction block connector C-78 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-27, D-26 or junction block connector C-78 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.
Q: Is the wiring harness between rear dome light connector D-27 (terminal 1) and ETACS-ECU connector C-95 (terminal 6) in good condition?
YES: No action is necessary and testing is complete.
NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the rear dome lights illuminate normally.
STEP 15. Check rear dome light connector D-27 and ETACS-ECU connector C-95 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q: Are rear dome light connector D-27 and ETACS-ECU connector C-95 in good condition?
YES: Go to Step 16.
NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that the rear dome lights illuminate normally.
STEP 16. Check the wiring harness between rear dome light connector D-27 (terminal 2) and ETACS-ECU connector C-95 (terminal 5).
NOTE: Also check intermediate connectors C-27, D-26 and junction block connector C-78 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-27, D-26 or junction block connector C-78 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.
Q: Is the wiring harness between rear dome light connector D-27 (terminal 2) and ETACS-ECU connector C-95 (terminal 5) in good condition?
YES: No action is necessary and testing is complete.
NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the rear dome lights illuminate normally.
STEP 17. Check the trunk light bulb.
Q: Is the trunk light bulb in good condition?
YES: Go to Step 18.
NO: Replace the bulb. Verify that the trunk lights illuminate normally.
STEP 18. Check the input signal by using the pulse check mode of the monitor.
Check the input signals from the trunk lid latch switch:
CAUTION:
To prevent damage to scan tool MB991502, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991502.
1. Connect scan tool MB991502 to the data link connector.
2. Operate scan tool MB991502 as follows:
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "PULSE CHECK."
3. When the trunk lid is opened and closed, check if scan tool MB991502 sounds or not.
Q: When the trunk lid is opened and closed, does scan tool MB991502 sound?
YES: Go to Step 19.
NO: Refer to Inspection Procedure N-9 "ETACS-ECU does not receive any signal from the trunk lid latch switch."
STEP 19. Check the ETACS-ECU line of the power supply circuit to the trunk light. Test at trunk light connector F-11.
1. Disconnect trunk light connector F-11 and measure the voltage available at the wiring harness side of the connector.
2. Measure the voltage between terminal 1 and ground.
- The voltage should measure approximately 12 volts (battery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery positive voltage)?
YES: Go to Step 22.
NO: Go to Step 20.
STEP 20. Check trunk light connector F-11 and ETACS-ECU connector C-95 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q: Are trunk light connector F-11 and ETACS-ECU connector C-95 in good condition?
YES: Go to Step 21.
NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that the trunk lights illuminate normally.
STEP 21. Check the wiring harness between trunk light connector F-11 (terminal 1) and ETACS-ECU connector C-95 (terminal 6).
NOTE: Also check junction block connector C-77 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If junction block connector C-77 is damaged, Repair or replace the damaged component(s) as described in Harness Connector Inspection.
Q: Is the wiring harness between trunk light connector F-11 (terminal 1) and ETACS-ECU connector C-95 (terminal 6) in good condition?
YES: No action is necessary and testing is complete.
NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the trunk lights illuminate normally.
STEP 22. Check trunk light connector F-11 and ETACS-ECU connector C-94 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q: Are trunk light connector F-11 and ETACS-ECU connector C-94 in good condition?
YES: Go to Step 23.
NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that the trunk lights illuminate normally.
STEP 23. Check the wiring harness between trunk light connector F-11 (terminal 2) and ETACS-ECU connector C-94 (terminal 52).
NOTE: Also check intermediate connector C-67 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-67 is damaged, repair or replace the connector as described in Harness Connector Inspection.
Q: Is the wiring harness between trunk light connector F-11 (terminal 2) and ETACS-ECU connector C-94 (terminal 52) in good condition?
YES: Replace the ETACS-ECU. Verify that the trunk lights illuminate normally.
NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the trunk lights illuminate normally.