Operation CHARM: Car repair manuals for everyone.

Inspection Procedure H-8

Headlight and Taillight: The high-beam indicator light does not illuminate.

High-beam Indicator Light Circuit Part 1:




High-beam Indicator Light Circuit Part 2:






TECHNICAL DESCRIPTION (COMMENT)
If the high-beam indicator light does not illuminate, the high-beam indicator light bulb or the ETACS-ECU may be defective.

TROUBLESHOOTING HINTS
- The high-beam indicator light bulb may be defective
- The ETACS-ECU may be defective
- The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector

DIAGNOSIS

Required Special Tool:
- MB991223: Harness Set

STEP1. Check the headlight operation.

Q: Do the headlights illuminate?

YES: Go to Step 2.

NO: Repair the headlights first.







STEP 2. Check at ETACS-ECU connector C-94 in order to check the high-beam indicator light circuit.

1. Disconnect ETACS-ECU connector C-94, and measure at the wiring harness side.
2. Turn the ignition switch to the "ON" position.
3. Connect terminal 72 to ground.

Q: Does the high-beam indicator light illuminate?

YES: Replace the ETACS-ECU. Verify that the high-beam indicator light illuminates normally.

NO: Go to Step 3.




STEP 3. Check the high-beam indicator light bulb.

Q: Is the high-beam indicator light bulb in good condition?

YES: Go to Step 4.

NO: Replace the high-beam indicator light bulb. Verify that the high-beam indicator light illuminates normally.




STEP 4. Check the combination meter (printed-circuit board).

1. Remove the combination meter.
2. Remove the high-beam indicator light bulb. Then measure the resistance value between the bulb terminals.
3. Install the bulb to the combination meter, and then measure the resistance value between connector C-29 terminal Nos.22 and 23. The measured resistance value should be roughly the same as the value measured in Step (2).

Q: Are these two resistance values extremely different?

YES: Repair or replace the combination meter (printed circuit board). Check that the headlight-beam indicator light illuminates normally.

NO (roughly the same): Go to Step 5.







STEP 5. Check the fusible link (1) line of the power supply circuit to the high-beam indicator light. Test at combination meter connector C-29.

1. Disconnect combination meter connector C-29 and measure the voltage available at the wiring harness side of the connector.

2. Measure the voltage between terminal 23 and ground.
- The measurement value should be 12 volts.

Q: Is the measured voltage approximately 12 volts (battery positive voltage)?

YES: Go to Step 8.

NO: Go to Step 6.




STEP 6. Check combination meter connector C-29 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q: Is combination meter connector C-29 in good condition?

YES: Go to Step 7.

NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Check that the high-beam indicator light illuminates normally.













STEP 7. Check the wiring harness between combination meter connector C-29 (terminal 23) and fusible link (1).

NOTE: Also check junction block connectors C-84, C-89 and intermediate connector C-66 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If junction block connectors C-84, C-89 or intermediate connectors C-66 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.

Q: Is the wiring harness between combination meter connector C-29 (terminal 23) and fusible link (1) in good condition?

YES: No action is necessary and testing is complete.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector.Repair the wiring harness as necessary. Verify that the high-beam indicator light illuminates normally.







STEP 8. Check combination meter connector C-29 and ETACS-ECU connector C-94 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q: Are combination meter connector C-29 and ETACS-ECU connector C-94 in good condition?

YES: Go to Step 9.

NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Check that the high-beam indicator light illuminates normally.







STEP 9. Check the wiring harness between combination meter connector C-29 (terminal 22) and ETACS-ECU connector C-94 (terminal 72).

Q:
Is the wiring harness between combination meter connector C-29 (terminal 22) and ETACS-ECU connector C-94 (terminal 72) in good condition?

YES: No action is necessary and testing is complete.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the high-beam indicator light illuminates normally.