Operation CHARM: Car repair manuals for everyone.

Inspection Procedure E-3

Keyless Entry System: The trunk lid opener is not operated by the keyless entry transmitter.

NOTE: This troubleshooting procedure requires the use of scan tool MB991502 and SWS monitor kit MB991862. For details on how to use the SWS monitor, refer to "How to use SWS monitor".

Transmitter Input Circuit:






CIRCUIT OPERATION
A receiver is incorporated in the ETACS-ECU. This receiver receives a lock, unlock or trunk open signal from the transmitter.

TROUBLESHOOTING HINTS
- The transmitter may be defective
- The ETACS-ECU may be defective
- The trunk lid opener actuator may be defective

DIAGNOSIS

Required Special Tools:
- MB991223: Harness Set
- MB991502: Scan Tool (MUT-II)
- MB991862: SWS Monitor Kit




STEP 1. Check the input signal by using the pulse check mode of the monitor.

Check the input signals from the transmitter.

CAUTION:
To prevent damage to scan tool MB991502, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991502.

1. Connect scan tool MB991502 to the data link connector.

2. Operate the scan tool as follows:
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "PULSE CHECK."

3. Push the transmitter "TRUNK" switch.
4. Check that scan tool MB991502 sounds.

Q: When the transmitter "TRUNK" switch is pushed, does scan tool MB991502 sound?

YES: Go to Step 2.

NO: Refer to Inspection Procedure N-11 "The ETACS-ECU does not receive signal from lock, unlock, panic or trunk switch".




STEP 2. Check the trunk lid opener actuator assembly.

1. Remove the trunk lid opener actuator assembly. Refer to Trunk Lid Removal and Installation.




2. Check that the trunk lid opener actuator assembly lever function.

Q: Is the trunk lid opener actuator assembly in good condition?

YES: Go to Step 3.

NO: Replace the trunk lid opener actuator assembly. Verify that the trunk lid opener actuator assembly works normally.







STEP 3. Measure at trunk lid opener actuator assembly connector F-27 in order check the ground system to trunk lid opener actuator assembly.

1. Disconnect trunk lid opener actuator assembly connector F-27, and measure at the harness side.

2. Measure the resistance value between terminal 2 and ground.
- The resistance should measure 2 ohms or less.

Q: Is the measured resistance 2 ohms or less?

YES: Go to Step 6.

NO: Go to Step 4.

STEP 4. Check the trunk lid opener actuator connector F-27 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q: Is the trunk lid opener actuator connector F-27 in good condition?

YES: Go to Step 5.

NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that the trunk lid opener work normally.




STEP 5. Check the wiring harness between trunk lid opener actuator connector F-27 (terminal 2) and ground

Q: Is the wiring harness between the trunk lid opener actuator connector F-27 (terminal 2) and the ground in good condition?

YES: No action is necessary and testing is complete.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the trunk lid opener work normally.







STEP 6. Check the trunk lid opener actuator connector F-27 and ETACS-ECU connector C-93 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q: Are trunk lid opener actuator connector F-27 and ETACS-ECU connector C-93 in good condition?

YES: Go to Step 7.

NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that the trunk lid opener work normally.










STEP 7. Check the wiring harness between trunk lid opener actuator connector F-27 (terminal 1) and ETACS-ECU connector C-93 (terminal 32).

NOTE: Also check intermediate connector C-67 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-67 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.

Q: Is the wiring harness between the trunk lid opener actuator connector F-27 (terminal 1) and ETACS-ECU connector C-93 (terminal 32) in good condition?

YES: Replace the ETACS-ECU. Verify that the Keyless entry system work normally.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that the keyless entry system work normally.