Operation CHARM: Car repair manuals for everyone.

Inspection Procedure C-2

Central Door Locking System: Some doors do not lock or unlock.

Central Door Lock Circuit Part 1:




Central Door Lock Circuit Part 2:






CIRCUIT OPERATION
- The ETACS-ECU operates the central door lock system according to the following signals:
- Driver's or passenger's door lock actuator switch
- Driver's or passenger's door lock key cylinder switch
- Door lock switch, which is incorporated in the power window main switch or power window sub switch (front RH)
- The ETACS-ECU locks or unlocks all the doors by operating the central door lock relay (incorporated in the ECU) in response to input signals.

TECHNICAL DESCRIPTION (COMMENT)
The wiring harness between the door lock actuator or the ETACS-ECU and the door lock actuator may defective.

TROUBLESHOOTING HINTS
- The driver's door lock actuator, front passenger's door lock actuator or rear door lock actuator may be defective
- The ETACS-ECU may be defective
- The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector

DIAGNOSIS

Required Special Tool:
- MB991223: Harness Set

STEP 1. Check which door lock is defective.

Q: Which of the door locks is defective?
Driver's door : Go to Step 2.
Front passenger's door : Go to Step 6.
Rear door (LH): Go to Step 10.
Rear door (RH): Go to Step 14.




STEP 2. Check the driver's door lock actuator.




Remove the driver's door lock actuator, and check it. Refer to Door Handle and Latch.

Q: Does the driver's door lock actuator work normally?

YES: Go to Step 3.

NO: Replace the driver's door lock actuator. Verify that all the doors can be locked and unlocked normally.







STEP 3. Check ETACS-ECU connectors C-93, C-95 and driver's door lock actuator connector E-15 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q: Are ETACS-ECU connectors C-93, C-95 and driver's door lock actuator connector E-15 in good condition?

YES: Go to Step 4.

NO: Repair or check the connector. Refer to Harness Connector Inspection. Verify that all the doors can be locked and unlocked normally.










STEP 4. Check the wiring harness from ETACS-ECU connector C-93 (terminal 22) to driver's door lock actuator connector E-15 (terminal 4).

NOTE:
Also check intermediate connector C-68 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-68 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.

Q: Is the wiring harness from ETACS-ECU connector C-93 to driver's door lock actuator connector E-15 in good condition?

YES: Go to Step 5.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair or replace the damaged component(s). Verify that the central door locking system works normally.













STEP 5. Check the wiring harness from ETACS-ECU connector C-95 (terminal 12) to driver's door lock actuator connector E-15 (terminal 6).

NOTE: Also check intermediate connector C-68 and junction block connector C-84 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-68 or junction block connector C-84 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.

Q: Is the wiring harness from ETACS-ECU connector C-95 to driver's door lock actuator connector E-15 in good condition?

YES: Replace the ETACS-ECU. Verify that all the doors can be locked and unlocked normally.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair or replace the damaged component(s). Verify that the central door locking system works normally.




STEP 6. Check the front passenger's door lock actuator.




Remove the passenger's door lock actuator, and check it. Refer to Door Handle and Latch.

Q: Is the front passenger's seat door lock actuator normal?

YES: Go to Step 7.

NO: Replace the front passenger's seat door lock actuator. Verify that all the doors can be locked and unlocked normally.







STEP 7. Check ETACS-ECU connector C-95 and front passenger's door lock actuator connector E-07 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q: Are ETACS-ECU connector C-95 and passenger's seat door lock actuator connector E-07 in good condition?

YES: Go to Step 8.

NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that all the doors can be locked and unlocked normally.













STEP 8. Check the wiring harness from ETACS-ECU connector C-95 (terminal 12) to front passenger's door lock actuator connector E-07 (terminal 4).

NOTE: Also check intermediate connector C-72 and junction block connector C-84 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-72 or junction block connector C-84 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.

Q: Is the wiring harness from ETACS-ECU connector C-95 to front passenger's door lock actuator connector E-07 in good condition?

YES: Go to Step 9.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary.













STEP 9. Check the wiring harness from ETACS-ECU connector C-95 (terminal 13) to front passenger's door lock actuator connector E-07 (terminal 6).

NOTE:
Also check intermediate connector C-72 and junction block connector C-84 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-72 or junction block connector C-84 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.

Q: Is the wiring harness from ETACS-ECU connector C-95 to front passenger's door lock actuator connector E-07 in good condition?

YES: Replace the ETACS-ECU. Verify that all the doors can be locked and unlocked normally.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that all the doors can be locked and unlocked




STEP 10. Check the rear door lock actuator (LH).




Remove the rear door lock actuator (LH), and check it. Refer to Door Handle and Latch.

Q: Does the rear door lock actuator (LH) work normally?

YES: Go to Step 11.

NO: Replace the rear door lock actuator (LH). Verify that all the doors can be locked and unlocked normally.







STEP 11. Check ETACS-ECU connector C-95 and rear door lock actuator (LH) connector E-11 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q: Are ETACS-ECU connector C-95 and rear door lock actuator LH.connector E-11 in good condition?

YES: Go to Step 12.

NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that all the doors can be locked and unlocked normally.













STEP 12. Check the wiring harness from ETACS-ECU connector C-95 (terminal 12) to rear door lock actuator (LH) connector E-11 (terminal 4).

NOTE: Also check intermediate connector D-19 and junction block connector C-77 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector D-19 or junction block connector C-77 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.

Q: Is the wiring harness between ETACS-ECU connector C-95 and rear door lock actuator LH.connector E-11 in good condition?

YES: Go to Step 13.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that all the doors can be locked and unlocked













STEP 13. Check the wiring harness from ETACS-ECU connector C-95 (terminal 13) to rear door lock actuator (LH) connector E-11 (terminal 6).

NOTE: Also check intermediate connector D-19 and junction block connector C-77 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector D-19 or junction block connector C-77 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.

Q: Is the wiring harness between ETACS-ECU connector C-95 and rear door lock actuator (LH) connector E-11 in good condition?

YES: Replace the ETACS-ECU. Verify that all the doors can be locked and unlocked normally.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that all the doors can be locked and unlocked




STEP 14. Check the rear door lock actuator (RH).




Remove the rear door lock actuator (RH), and check it. Refer to Door Handle and Latch.

Q: Does the rear door lock actuator (RH) work normally?

YES: Go to Step 15.

NO: Replace the rear door lock actuator (RH). Verify that all the doors can be locked and unlocked normally.







STEP 15. Check ETACS-ECU connector C-95 and rear door lock actuator (RH) connector E-10 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q: Are ETACS-ECU connector C-95 and rear door lock actuator (RH) connector E-10 in good condition?

YES: Go to Step 16.

NO: Repair or replace the damaged component(s). Refer to Harness Connector Inspection. Verify that all the doors can be locked and unlocked normally.
















STEP 16. Check the wiring harness from ETACS-ECU connector C-95 (terminal 12) to rear door lock actuator (RH) connector E-10 (terminal 6).

NOTE:
Also check junction block connector C-84 and intermediate connectors C-71 and D-07 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If junction block connector C-84, intermediate connector C-71 or D-07 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.

Q: Is the wiring harness between ETACS-ECU connector C-95 and rear door lock actuator (RH) connector E-10 in good condition?

YES: Go to Step 17.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that all the doors can be locked and unlocked
















STEP 17. Check the wiring harness from ETACS-ECU connector C-95 terminal (13) to rear door lock actuator (RH) connector E-10 (terminal 4).

NOTE:
Also check junction block connector C-84 and intermediate connectors C-71 and D-07 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If junction block connector C-84, intermediate connector C-71 or D-07 is damaged, repair or replace the damaged component(s) as described in Harness Connector Inspection.

Q: Is the wiring harness between ETACS-ECU connector C-95 and rear door lock actuator (RH) connector E-10 in good condition?

YES: Replace the ETACS-ECU. Verify that all the doors can be locked and unlocked normally.

NO: The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Verify that all the doors can be locked and unlocked