Inspection Procedure B-2
Tone Alarm: Light reminder tone alarm function does not work normally.NOTE: This troubleshooting procedure requires the use of scan tool MB991502 and SWS monitor kit MB991862. For details on how to use the SWS monitor, refer to "How to use SWS monitor."
Light Reminder Tone Alarm Function:
CIRCUIT OPERATION
The ETACS-ECU operates the light reminder tone alarm function according to the following signals:
- Ignition switch (IG1): OFF
- Ignition key reminder switch: ON
- Driver's door switch: ON
- Taillight switch: ON
- Headlight switch: ON
The ETACS-ECU operates the light reminder tone alarm function under the following conditions:
- Ignition switch: "LOCK" (OFF) position
- Ignition key: Removed from the ignition key cylinder
- Driver's door: open
- Taillight or headlight: Illuminating
TECHNICAL DESCRIPTION (COMMENT)
If the function does not work normally, the input circuit system from the switches or the ETACS-ECU may be defective (refer to "CIRCUIT OPERATION").
TROUBLESHOOTING HINTS
- The front door switches may be defective
- The column switch (turn-signal light and lighting switch) may be defective
- The ETACS-ECU may be defective
- The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector
DIAGNOSIS
Required Special Tools:
- MB991223: Harness Set
- MB991502: Scan Tool (MUT-II)
- MB991862: SWS monitor kit
STEP 1. Use scan tool MB991502 to select "ECU COMM CHK" on the SWS monitor display.
Check the following ECUs:
- ETACS-ECU
- Column switch (column-ECU)
CAUTION:
To prevent damage to scan tool MB991502, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991502. Connect the DLC harness before connecting the column-ECU harness. Be sure to connect SWS monitor kit MB991862 after turning on scan tool MB991502.
1. Connect scan tool MB991502 to the data link connector.
2. Connect SWS monitor kit MB991862 to the column switch connector.
3. Turn the ignition switch to the "LOCK" OFF.position.
4. Operate scan tool MB991502 according to the procedure below to display "ECU COMM CHK."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "ECU COMM CHK."
5. Scan tool MB991502 should show "OK" on the "ECU COMM CHK" menus for both the "ETACS ECU" and the "COLUMN ECU" menus.
Q: Is "OK" displayed on both the "ETACS ECU" and "COLUMN ECU" menus?
"OK" are displayed for all the items : Go to Step 2.
"NG" is displayed on the "ETACS ECU" menu : Refer to Inspection Procedure A-3 "Communication with ETACS-ECU is not possible."
"NG" is displayed on the "COLUMN ECU" menu : Refer to Inspection Procedure A-2 "Communication with column switch (column-ECU) is not possible."
STEP 2. Check the input signal by using "FUNCTION DIAG." menu of the SWS monitor.
Check the input signals from the following switches:
- Ignition switch: OFF (key removed)
- Lighting switch: TAIL or HEAD
- Driver's door: open
- Front passenger's door: closed
Operate scan tool MB991502 according to the procedure below to display "LGT MONI. ALRM."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "FUNCTION DIAG."
5. Select "BUZZER."
6. Select "LGT MONI. ALRM."
Check that normal conditions are displayed on the items described in the table.
NOTE: The scan tool display changes when the driver's or the front passenger's door is opened. If any of the doors is open, the system can not be checked correctly.
Q: Does the scan tool display "HEADLIGHT SW", "TAILLIGHT SW", "IG SW IG1", "FRONT DOOR SW", "H/L AUTO-CUT" and "BUZZER" as normal condition?
YES: Replace the ETACS-ECU. The light reminder tone alarm function should now work normally.
NO:
- Normal condition is not displayed for "HEADLIGHT SW": Refer to Inspection Procedure M-5 "ETACS-ECU does not receive any signal from the headlight switch."
- Normal condition is not displayed for "TAILLIGHT SW": Refer to Inspection Procedure M-5 "ETACS-ECU does not receive any signal from the taillight switch."
- Normal condition is not displayed for "IG SW (IG1)": Refer to Inspection Procedure M-2 "ETACS-ECU does not receive any signal from the ignition switch (IG1)."
- Normal condition is not displayed for "FRONT DOOR SW": Refer to Inspection Procedure M-4 "ETACS-ECU does not receive any signal from the driver's or the front passenger's door switch."
- Normal condition is not displayed for "H/L AUTO-CUT": Refer to Inspection Procedure H-9 "Headlight automatic shutdown function does not work normally."
- Normal condition is not displayed for "BUZZER": Replace the ETACS-ECU. The light reminder tone alarm function should now work normally.