Operation CHARM: Car repair manuals for everyone.

Selector Mechanism, Checking






Selector Mechanism, Checking

There is a risk of injury and accident from accidentally engaging a gear when the engine is running.

• Before performing any work with the engine running, move the selector lever into "P" and press the parking brake button to set the electromechanical parking brake.

• Pay attention to the safety precautions when driving. Refer to => [ Safety Precautions ] Safety Precautions.

• Perform all tests. If the specified values are not reached, perform "Guided Fault Finding" with vehicle diagnostic tester.

Overview

• 1. Check the gear locks / selector lever release button (E681)

• 2. Selector mechanism function test

• 3. Check the displays in the instrument cluster

• 4. Check the ignition key lock

• Under the new "shift-by-wire" operating/shift concept, there is no longer a mechanical connection between the selector lever and the transmission. "Shift-by-wire" also means "electric shift".

• The shift-by-wire concept is a new way of operating. What is new is that the selector lever does not move into shift gate for each selected driving gear as before, but rather it always returns to the neutral position similar to a joystick. This means the position of the selector lever and gear selected do not match like before.

• Any complaints due to malfunctions should be corrected.

• Check the selector mechanism thoroughly to make sure it functions correctly.

Check the 1st Gear Locks / Selector Lever Release Button (E681).






• The electromechanical parking brake is closed.

- Start the engine and let it run at idle.

1. Check 1.:

- Move the selector lever to "P".

Specified Values

• "P" must appear in the instrument cluster and in the selector lever transmission range position display unit (Y26) , - 2 -.

2. Check 1.:

• Do not press the brake pedal.

- Press the selector lever release button, - 1 - and try to move the gearshift lever toward the rear.

Specified Values

• It should not be possible to move the selector lever toward the rear (locked).

• "P" must remain engaged.

• The following message must appear in the instrument cluster: "Press brake pedal to select a gear".

3. Check 1.:

• Do not press the selector lever release button - 1 -.

- Press the brake pedal and try to move the selector lever toward the rear.

Specified Values

• It should not be possible to move the selector lever toward the rear (locked).

• "P" must remain engaged.

4. Check 1.:

- Press the brake pedal and hold it down.

- Press the selector lever release button, - 1 -.

- Move the selector lever into "D".

Specified Values

• "D" must appear in the instrument cluster and in the selector lever transmission range position display unit, - 2 -.

• "D and S" - D/S - must always appear in the selector lever transmission range position display unit, - 2 -.

5. Check 1.:

- Press the brake pedal and hold it down.

• Do not press the selector lever release button, - 1 -.

- Move the selector lever forward.

Specified Values

• It should not be possible to move the selector lever toward the front (locked).

• "D" must remain engaged.

- Move the selector into "S".

Specified Values

• "S" must appear in the instrument cluster.

If the specified values are not obtained:

- Make sure the selector lever handle is installed correctly. Refer to => [ Selector Lever Handle ] Selector Lever Handle.

- Perform "Guided Fault Finding" using the vehicle diagnostic tester.

2. Selector Mechanism Function Test






- Start the engine.

1. Check 2.:

- Move the selector lever into "D".

- Drive

- Move the selector lever into "N".

• Do not press the selector lever release button - 1 - or the brake pedal.

- Move the selector into "D".

Specified Values

• The selector lever must not lock up when the vehicle is moving faster than 5 km/h and when moving the selector lever into "N". The selector lever can be moved into "D".

• The locking magnets inside the selector mechanism will lock the selector lever after approximately 1 second if the vehicle is moving slower than 2 km/h (almost stationary) and when the selector lever is in "N". The selector lever can be moved into "D" only when the brake pedal is pressed.

2. Check 2.:

- Move the selector lever into "N".

• Do not press the selector lever release button - 1 -.

- Press the brake pedal.

Specified Values

• It is not possible to move the selector lever forward and it is not possible to shift into "R".

• The selector lever must stay in "N".

3. Check 2.:

- Move the selector lever into "D".

- Move the selector lever into "N".

- Move the selector lever into "R".

- Move the selector lever to "P".

Specified Values

• The selected gear must appear in the instrument cluster as well as in the selector lever transmission range position display unit - 2 -. The displays must match.

• "D and S" - D/S - must always appear in the selector lever transmission range position display unit, - 2 -.

- Do not press the brake pedal.

Specified Values

• The selector lever is locked and cannot be moved out of "P" when the selector lever release button - 1 - is pressed.

If the specified values are not obtained:

- Make sure the selector lever handle is installed correctly. Refer to => [ Selector Lever Handle ] Selector Lever Handle.

- Perform "Guided Fault Finding" using the vehicle diagnostic tester.

3. Checking the Displays Inside the Instrument Cluster






- Start the engine.

1. Check 3.:

Specified Values

• The selected gear must also appear in the instrument cluster for at least 5 seconds when the selector lever release button, - 1 - is pressed.

2. Check 3.:

- Move the selector lever into "D" and press the - M - button in the steering wheel to select the manual mode "M" (tiptronic)






• "M" must appear in the instrument cluster.

- Use the - (+) - and - (-) - paddles in the steering wheel with the manual mode "M" (Tiptronic) selected and while driving.

• The display in the instrument cluster must also change each time a higher (+) or lower (-) gear is selected.

3. Check 3.:

- Move the selector lever to "P".

- Turn off the engine.

- Turn on the ignition.

• Do not press the brake pedal.

- Press the selector lever release button, - 1 -.






Specified Values

• The following message must appear in the instrument cluster: "Press brake pedal and start engine to select R, N or D".

If the specified values are not obtained:

- Make sure the selector lever handle is installed correctly. Refer to => [ Selector Lever Handle ] Selector Lever Handle.

- Perform "Guided Fault Finding" using the vehicle diagnostic tester.

4. Check the Ignition Key Lock (vehicles with an ignition key lock)

1. Check 4.:

- Insert the key into the ignition lock.

- Start the engine.

- Move the selector lever into "D".

• The vehicle is standing.

- Turn off the ignition and leave the key inside the ignition lock.

Specified Values

• "P" must engage automatically and immediately (without moving the selector lever).

• "P" must appear in the instrument cluster and in the selector lever transmission range position display unit - 2 -.






2. Check 4.:

- Insert the key into the ignition lock.

- Start the engine.

- Move the selector lever into "N".

• The vehicle is standing.

- Turn off the ignition and leave the key inside the ignition lock.

- Open the driver door.

Specified Values

• The following message must appear in the instrument cluster: "Transmission not in P. Vehicle can roll away".

• A warning tone will also sound.

- Remove the key.

Specified Values

• "P" must engage automatically and immediately (without moving the selector lever).

• "P" must appear in the instrument cluster and in the selector lever transmission range position display unit, - 2 -.

If the specified values are not obtained:

- Make sure the selector lever handle is installed correctly. Refer to => [ Selector Lever Handle ] Selector Lever Handle.

- Perform "Guided Fault Finding" using the vehicle diagnostic tester.