Operation CHARM: Car repair manuals for everyone.

Lower Timing Chain Cover






Lower Timing Chain Cover

Special tools, testers and auxiliary items required

• Locking Pin (T10060 A)

• Counter Hold Tool (T10355)

• Thrust Piece (T10368)

Removing

- Remove the front noise insulation.

- Remove the front bumper cover and the bumper.

- Install the lock carrier in service position.






Risk of destroying due to reversed running direction on a used ribbed belt.

• Before removing ribbed belt, marking running direction with chalk or felt-tip pen for reinstallation later.

- To release ribbed belt tension, rotate tensioner in direction of - arrow -.

- Secure the tensioner with the (T10060 A).

- Remove ribbed belt.

- Remove the bolts - arrows - and pull the ribbed belt tensioning damper - 1 - off the sub-assembly bracket.






- Rotate the vibration damper using the (T10355) into the "TDC" position - arrow -.






• The notch on the vibration damper must line up with the arrow marking on the timing chain lower cover.

- Remove vibration damper bolt using (T10355).

- Remove the vibration damper.

• To avoid damaging the splines, only install the vibration damper bolt with the (T10368).

- Install the vibration damper bolt and (T10368) again.






The engine could be destroyed.

• In order not to change the valve timing, the crankshaft must not be moved out of the "TDC" position when the vibration damper bolt is removed.

- Remove the idler roller - 1 -.

- Remove the bolts - arrows - and remove the oil dipstick guide tube from the timing chain cover.






- Remove the bolts - 1 through 15 -.






- Pry off the lower timing chain cover; when doing this, begin at - 1 and 2 -.






• To avoid deformation, do not hold between the bolting points.

Installing

• For the correct tightening specifications, refer to => [ Timing Chain Covers Overview ] Timing Chain Covers Overview

• Silicon sealant, refer to the electronic parts catalog ETKA

• Note the expiration date of the silicone sealant.

• The cover must be installed within 5 minutes after the silicone sealant has been applied.

• Replace the bolts which are being tightened with an additional turn.

• Replace sealing rings, seals and self-locking nuts.

- Spray the sealing surface with sealant remover and allow it to work.

- Remove any sealant residue on the cylinder block using a flat blade scraper.

Danger of eye injury.

• Wear protective eyewear.

- Seal off both sides of the seal with tape to prevent contamination.

- Use a rotating plastic brush to remove any remaining sealing on the cover.






- Clean any oil or grease off the sealing surfaces.

- Install the cover using the old bolts and tighten to 8 Nm.

- Check between the cover and crankcase using a feeler gauge; the gap must not exceed 0.2 mm.

• If the gap exceeds 0.2 mm, replace the cover.

• It is not possible to measure between the cover the upper section of the oil pan, however check the sealing surface for evenness.

- Make sure both alignment bushings for centering the cover - arrows - are present.






- Cut the tube nozzle at the front marking (nozzle diameter: approximately 3 mm).






- Apply the silicone sealant on the clean sealing surface of the cover as illustrated.






• Thickness of sealant bead: 2 to 3 mm.

• The cover must be installed within 5 minutes after the silicone sealant has been applied.

• The sealant bead may not be thicker than specified, otherwise excess sealant could enter the oil pan and clog the oil intake tube.

- Mount the cover immediately and tighten the bolts, tightening sequence. Refer to => [ Timing Chain Lower Cover Tightening
Sequence ] Timing Chain Covers Overview.

• After installing cover, allow sealant to dry for approximately 30 minutes. Only after then may the engine oil be replenished.

- Install the ribbed belt tensioning damper. Refer to => [ Ribbed Belt Tensioner ] Service and Repair.

- Install the ribbed belt. Refer to => [ Ribbed Belt ] Ribbed Belt.

- Install the service position.

- Install the bumper and front bumper cover.

- Install the front noise insulation.

- Check the oil level.